One for All URC-7542 manual Search Method

Page 7
Press 9 9 1. The red light will blink twice
Press the TV key on your ONE FOR ALL 4.

The Search Method

If your device does not respond to the ONE FOR ALL 4 after you have tried all the codes listed for your brand, try searching for your code. The Search Method allows you to find the code for your device by scanning through all the codes contained in the memory of the ONE FOR ALL 4. The Search Method may also work if your brand is not listed at all.

Example: To search for your TV code:

1Switch your television on (not on standby) and aim your ONE FOR ALL at your TV.

2

3Press and hold down MAGIC until the ONE FOR ALL 4’s red light blinks twice (The red light will blink once and then twice).

4

5

Now slowly, alternate between TV and POWER, over and

 

over, until your television turns off. You may have to

 

press these keys many times (up to 200!), so please

 

 

be patient. Remember to keep pointing the ONE FOR

 

ALL 4 at your television when you press these keys.

6As soon as your television turns off, press MAGIC to store the code.

The ONE FOR ALL remote should now be ready to operate your device. Turn your device back on and try all the remote’s functions to ensure they are working properly. If some of the ONE FOR ALL’s commands are not operating correctly, try the search method again. You may be using the wrong code.

Important notes:

-To search for the code for another device follow the instructions above only press the appropriate device key instead of TV during steps 2 and 5.

-If the original remote control of your VCR does not have a POWER key, press PLAY instead of POWER during step 5.

Once you have Set-Up your ONE FOR ALL 4, you can blink back your SET-UP CODE for future reference.

Example: To blink out your Television code:

1

Press TV once.

2Press and hold MAGIC until the ONE FOR ALL 4’s TV key blinks twice (The red light will blink once and then twice).

3

4

5

Press 9 9 0. The red light will blink twice.

For the first digit of your four-digit code, press 1 and count all the red blinks. If there are no blinks, the digit is "0".

For the second digit, press 2 and count all the red blinks. If there are no blinks, the digit is "0".

6

For the third digit, press 3 and count all the red blinks.

 

If there are no blinks, the digit is "0".

7

For the fourth digit, press 4 and count all the red blinks. If

 

there are no blinks, the digit is "0". Now you have your

 

four-digit code.

Make sure you write your Television code in the boxes provided in the battery compartment and on page 8 for easy future reference.

Important note: To blink back the code for your other devices press the appropriate device key during step 1.

WWW.ONEFORALL.COM

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents URC-7542 About Your ONE for ALL Table of Contents10/11 Keypad Installing the BatteriesTeletext and Fastext Keys Volume +/- KeysMute Key Video Recorder KeysDevices can be found under the following keys InstallationSetting Up Your Devices Example To set up the ONE for ALL 4 for your televisionSearch Method Changing a Device Key Using the AUX keyQuick Code Reference Auto Scan Advanced FeaturesVolume Punch-Through Colour and BrightnessPress the device key TV or SAT Device SleeptimerONE for ALL Sleeptimer Setting the ONE for ALL SleeptimerProblem Solution Trouble-ShootingHelpful Hints Australia South Africa Customer Service3410805 IrelandAYR AGBASA AWAELG CTCDER DTSITS HCMICE ITCNAD MGAMTC MtecSEG RCARFT SBRTEC Adelsound 0004 Intervision 0000 AST TVAAGS AslfDST DDCDNR DNTSKR NTCOsat SCSXcom StviTPS UECPrinted on Recycled Paper 702075
Top Page Image Contents