Philips Rear-Projection HDTV Monitor setup guide Making Basic TV Connections, Best Viewing

Page 1

Quicki Use and Setup Guidei

HDTV Monitor

 

Rear-projection

CONTENTS

 

Important Notice/Warning

. .1

Making Basic TV Connections

1–2

Operating the Television and Remote Control

2–3

Using the Installation Features

4–6

Using the Picture-in-Picture (PIP) Feature

6–7

Adjusting the Manual Converge Controls

. .8

As an Energy Star® Partner, Philips Consumer Electronics has determined this product meets the Energy Star® guidelines for energy efficiency. Energy Star® is a U.S. registered mark. Using products with the Energy Star® label can save energy. Saving energy reduces air pollution and lowers utility bills.

IMPORTANT

This owner's manual is used with several differ- ent television models. Not all features (and draw- ings) discussed in this manual will necessarily match those found with your television set. This is normal and does not require that you contact your dealer or request service.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR EXCESSIVE MOISTURE.

MAKING BASIC TV CONNECTIONS

BEST VIEWING

The major benefit of this projection television is its large view-

ing screen. To see this large screen at its best, test various locations in the room to find the optimal spot for viewing.

NOTE: Be sure to allow a free flow of air to and from the per- forated back cover of the set.

To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot—for example, in direct sunlight or near a heating appliance.

Magnetic fields, such as those of external speak- ers, may cause the picture to distort if the speak- ers are placed too close to the television. Move the magnetic field source away from the TV until there is no picture distortion.

CABLES AND CONNECTORS

If you are new to making TV hookups, you may want to read this section. (The cables and connectors discussed are not sup-

plied with your set. You can buy them at most stores that sell audio or video products. Or call our Customer Care Center at 1-800-531-0039.)

This publication provides you with examples of basic connections. See pages 6–17 in the Directions for Use manual for more infor- mation on connections, along with connection examples.

A 75-ohm coaxial cable connects signals from an antenna or a cable TV company to the antenna jack on the back of the TV. Coaxial cables use “F” connectors.

A two-way signal splitter enables you to take a single antenna or cable TV signal and supply it to two different inputs.

A 300- to 75-ohm twin-lead adapter accepts the antenna cables (called twin-lead wires) from an antenna, allowing you to connect the antenna signal to the TV.

Video and audio cables with standard RCA (phono) connectors con- nect the video and audio jacks of accessory devices such as VCRs and DVD players to the jacks on the TV.

To simplify making connections, the connectors are usually color coded. The jacks on your TV are likewise color coded to match the colors of the connectors. The coding is as follows: yellow for video (composite) and red and white for the right and left audio channels, respectively. Use an audio cable with a white connector when making mono,

or nonstereo, connections. The connectors of video cables used to connect component video or RGB (high-resolution) jacks are often color coded red, green, and blue. Component video connec- tions provide you with the highest possible color and picture resolution.

An S-Video cable connects devices such as DVD players, VCRs, or camcorders to your TV. S-Video provides better picture per-

formance than regular (com- posite) video connections. S-Video cables can be used

only with S-Video-compatible accessory devices. You must also connect the left and right audio cables along with S-Video because the S-Video jack carries only the picture signal, not the sound.

A DB15 cable makes an RGB connection to the HD INPUT-AV 5 jack on the rear of the TV.

ANTENNA OR CABLE TV

This section shows you how to make a basic TV connection

Coaxial Cable

Cable TV

using a cable TV or antenna signal.

Lead-in from

Company

If you have cable TV service, you’ll simply connect the coaxial cable lead-in from the cable TV company to your TV. If you intend to connect a VHF/UHF antenna, you may need a 300- to 75-ohm adapter, which is not supplied with your TV.

Cable TV Company

NOTE: You should be able to buy optional accessories such as a VHF/UHF antenna or a 300- to 75-ohm adapter at most stores that sell electronics. Or you can call our Customer Care Center at 1-800-531-0039.

1 Connect the Cable TV or antenna signal to the ANTENNA IN 75jack on the rear of the TV.

NOTE: If you are using an antenna with a round coaxial cable (75), then you are ready to connect to the back of the TV. If your antenna has a flat, twin-lead wire (300), you must first attach the antenna wires on a 300- to 75- ohm adapter. Then push the round end of the adapter onto the ANTENNA IN 75jack on the rear of the TV.

2 Insert the TV’s power plug into the wall power outlet.

OR

 

1

 

Rear of TV

 

 

 

Coaxial Cable

 

 

 

 

ANTENNA IN 75

INPUT-AV 1

OUTPUT

INPUT-AV 2

 

 

Y

 

 

 

VIDEO

 

 

VIDEO

 

S-VIDEO

 

 

S-VIDEO

 

Pb

 

L

 

L

 

 

 

L

 

 

L

 

AUDIO

Pr

 

AUDIO

 

R

 

 

R

300- to 75-ohm Adapter

Outdoor or Indoor Antenna

(Combination VHF/UHF)

Twin-lead Wire

The combination antenna receives normal

 

broadcast channels 2–13 (VHF) and 14–69 (UHF).

HD INPUT-AV 5

HD INPUT-AV 4

G/Y

R/Pr

B/Pb

V

L L

SYNC

AUDIOAUDIO

H

RR

Coaxial Cable

Lead-in from Antenna

3135 035 20751

Image 1
Contents Making Basic TV Connections Cables and ConnectorsBest Viewing Antenna or Cable TVRemote Control Operating the Television and Remote ControlCable Converter Boxes TelevisionTV VCR ACC Tuner Mode Using the Installation FeaturesLanguage Auto ProgramChannel Edit Use the number buttons on your remote control to inputFollow steps 1-3 above, then press the Cursor Ring After you have input the time, press the CursorName Using the PICTURE-IN-PICTURE PIP FeatureMaking PIP Connections Adjusting Color and Tint Using the PIP ButtonsViewing Pictures Manual Converge Controls AdjustingConverge RED/BLUE Multipoint RED/BLUE