Philips TP3297B1 Press the Power button on, Device your are attempting to program to turn on

Page 41

SETTING THE REMOTE CONTROL TO WORK WITH OTHER DEVICES

Search Method

Your TV remote can be set to work various external devices

such as VCRs, Cable Boxes, Satellite Receivers, DBS, DVD, etc. by what is called the search method of remote control pro- gramming.

If the “Remote Code” number method shown on the previous page did not set your remote to work your external device, then follow the easy steps listed below.

Please read steps 1-4 before beginning.

BEGIN

Press the POWER button on

the device your are attempting to program to turn ON.

Place the TV/VCR/ACC

Mode Switch in the proper posi-

tion.

Press the VCR RECORD and the SMART SOUND but- tons simultaneously and hold

them down.

The device will begin to change channels after the remote identifies the correct code. When the channels start to change release the VCR RECORD and SMART SOUND buttons. The remote should be ready to oper- ate the device.

SMART HELP

This method can take up to two minute to preform.

Don’t let the device scan up more than five channels. If you do the remote may pass up the right code and another two minute search cycle will have to be repeated.

If no channel change happens within two minutes, repeat steps 1-4. Should a channel change still not occur, the remote will not work the desired device.

Satellite Receiver,
DBS, DVD, or
similar device
Cable Converter	070809 06
1		07
1		0809
	06	0809
		0708
VCR		09
VCR

2	LOCATOR			POWER	4
				POWER

TV	AV	ON/OFF	POSITION	FREEZE
VCR	SWAP	SOURCE	PIP CH
			UP	DN

ACC

SMARTSMART

SOUNDPICTURE

MENUSURF

3

VOL			CH
	MUTE
CC	STATUS	CLOCK	A/CH
	EXIT	TV/VCR
SLEEP			TUNER
			A/B
VCR			MULTI

RECORDMEDIA

INCREDIBLE

STEREO

3

41

Image 41

Contents TP3297B1 Warranty Verification Safety Instructions Read before operating equipment Table of Contents SET-UP and Quick USE Guide FeaturesButtons to adjust the selected control HOW to Adjust the TV PicturePress the STATUS/EXIT button To remove the menu from the screenPress the Cursor Down button until the word Features Setting the TV’S ClockPress the Numbered buttons Cursor UP or CursorRemote to show the onscreen menu Activating the TV’S on Timer ControlPress the Menu button on Button again to highlight the channel indicator area Selecting the TV’S on Timer ChannelPress the Cursor UP or Cursor Down buttons to Setting the TV’S on Timer TunerPress the Cursor Down Use the Cursor UP or CUR Setting the TV’S on Timer Start TimeTo enter the desired start up time Setting the TV’S on Timer Display Movie Ratings Understanding SmartlockEnter current access code Using Smartlock Setting UP the Access CodeDown to highlight SmartLock controlPress the Channel + or Using Smartlock Blocking ChannelsExternal inputs on the rear of the TV Input jacks. Select AV 1 or AV 2Press the Cursor Right Button to access the movie ratings Using Smartlock Movie RatingBe highlighted Button to select Movie RatingButton to select TV Rating Using Smartlock TV RatingAppear within the menu Options Using Smartlock BlockingUsing Smartlock Block Unrated Press the Menu button on the remote to show the on-screen Using Smartlock no RatingMenu Left button to set noExample Blocking is set to OFF Reviewing the Smartlock SettingsXxxx Viewing Blocked ProgrammingTurning on the Contrast + Control Turning on the Dynamic Noise Reduction Picture ControlTurning on the Incredible Picture Control Turn the INCR. PICT. feature on orPress the Cursor Down to highlight the INCR. PICT. con TrolCaption MODECC1, CC2, CC3, CC4, CC MUTE, or OFF Using the Closed Caption ControlSleep Using the Sleep Timer ControlUsing TREBLE, BASS, and Balance Sound Controls Will reproduce any stereo broad- cast signal it receives HOW to SET the TV for Stereo ProgramsButton to select the Sound menu Stereo selected the televisionUsing the TV Volume BAR Control Using the Incredible Stereo FeaturePress the Volume + or Press the Volume + or butUse the Cursor Right Or Cursor Left Using the TV Speaker Control and Audio Output JacksPress the Cursor Down button to select the Speaker Connect both external speak Using the Surround Sound External Speaker ConnectionsCable to the Video OUT jack on the back of the VCR. Then HOW to USE the AUDIO/VIDEO Input JacksConnect the Video yellow Not Supplied Connect the S-VIDEOPress the Power button on Using the Remote Locator FeatureWithin a few seconds a Chirping or beeping sound will Once you find the remoteNaled when the TV is turned Homing signalFor most homes this step would Not be needed but for your inforPress the SmartPicture button Press the Smart PicturePress the Smart Sound but Using the Smartsound ControlPress the Cursor Left Using the TV’S Channel Surf ControlPress the Surf button on Is necessary Setting the Remote Control to Work with Other DevicesPress the VCR Record Place the TV/VCR/ACCPress the SmartSound button Enter the THREE-DIGITDevice your are attempting to program to turn on Press the Power button onMode Switch in the proper posi Tion Remote VCR Code no Remote Control Direct Entry CodesRemote Dvdcode no Using the REMOTE’S VCR Buttons Hooking up PIP Using the PIP PICTURE-IN-PICTURE FeaturePress the PIP ON/OFF but Turn the TV and VCR orPress the PIP Source but AV 1, AV 2, S-VIDEOPress the PIP ON/OFF button Press the PIP ON/OFF butPressing the ON/OFF button a Press the PIP PositionAdjusting the PIP Color and Tint More PIP PICTURE-IN-PICTURE Connections First use an optional signalTelevision On the VCR to the Video in jack on the TVConnect the yellow Video Cable First connect the original cableConnect the ANT OUT jack on Tips if Something Isnt Working TV Displays Wrong Channel or No Channels AboveGlossary to Television Terms Index Philips Consumer Electronics Company Texas Limited Warranty