Philips DVD733/051 manual Important Note

Page 2

Important Note

DK

Advarsel:

Laserrudstråling ved åbning når sikkerhesafbrydere er ude af funktion. Undgå u tsættelse for stråling.

Bemærk:

Netafbryderen POWER er sekundært indkoblet og afbryder ikke strømmen fra nette. Den indbyggede netdel er derfor tilsluttet til lysnettet så længe netstikket sidder i stikkontakten.

S

Klass 1 laserapparat

Varning!

Om apparaten används på annat sätt än i denna bruksanvisning specificerats, kann användaren utsättas för laserstrålning, som översjruder gränsen för läserklass 1.

Observera!

Strömbrytaren POWER är sekundärt kopplad och inte bryter strömmen fråan nätet Den inbyggda nätdelen är därför ansluten till elnätet så länge stickproppen sitter i v ägguttaget.

N

Observer:

Nettbryteren POWER er sekundert innkoplet. Den innebygdenetdelen er derfor ikke frakoplet nettet så lenge apparatet er tilsluttet nettkontakten.

SF

Luokan 1 laserlaite + Klass 1 laserapparat

Varoitus!

Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle lasersäleilille.

Huom.

Toiminnanvalitsin POWER on kytketty toisiopuolelle, eikä se kytke laitetta irti sähköverkosta. Sisäänrakennettu verkko-osa on kytkettynä sähköverkkoon aina silloin, kun pistoke on pistorasiassa.

Important Note for Users in the UK

Mains plug

This apparatus is fitted with an approved 13 Amp plug.To change a fuse in this type of plug proceed as follows:

1Remove fuse cover and fuse.

2Fix new fuse which should be a BS1362 5 Amp, A.S.T.A. or BSI approved type.

3Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place.

If the mains plug contains a fuse, this should have a value of 5 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp.

Note:The severed plug must be disposed of to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured with the following code: blue = neutral (N), brown = live (L).

As these colours may not correspond with the colour markings identifying the terminals in your plug, proceed as follows:

Connect the blue wire to the terminal marked N or coloured black.

Connect the brown wire to the terminal marked L or coloured red.

Do not connect either wire to the earth terminal in the plug, marked E (or e) or coloured green

(or green and yellow).

Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the two wires.

Copyright in the U.K.

Recording and playback of material may require consent. See Copyright Act 1956 and The Performer’s Protection Acts 1958 to 1972.

3139 246 11xxx

Image 2
Contents 3141 015 Important Note Index General Information Laser safetyNever Make or Change Connections with the Power Switched on Contents Symbols Used in this Manual Supplied accessoriesSafety Information IntroductionFunctional Overview Front and Rear PanelsRemote Control Basic Connections Connecting to a TVPreparation If your receiver has a Mpeg 2 or Dolby Digital decoder Connecting to an Audio SystemConnecting to Optional Equipment Using the Remote Control Inserting batteries into the Remote ControlSwitching On Basic Playback General FeaturesOperation Video Control during playbackOSD On-Screen Display Special DVD Features Preview VCD Svcd Special VCD & Svcd FeaturesPlayback Control PBC Picture CD & MP3 CD Playback Picture CD and MP3 CD simultaneous playback General SetupBasic Operations Disc LockOSD Language Setup MenuVFD Dim Screen Saver Speaker setupDownmix mode C Dynamic Range CompressionSpdif OUT setup Spdif setupVideo Out Setup Lpcm 96K modeTV Type Video modeSmart Picture 169Audio language Preferences setupPersonal Picture setting Disc menu language PasswordSubtitle language Smart Navigator DefaultParental Control Specifications MaintenanceTroubleshooting Problem Solution3141 015 DVD733