Philips DVD825 manual Standard Connections Getting Started

Page 13

STANDARD CONNECTIONS

GETTING STARTED

 

 

CONNECTING THE POWER SUPPLY

1Plug the female end of the power cable supplied into the Power connector on the rear of the player.

2Plug the male end of the cord into an AC outlet.

- When the player is in the “OFF” position, it is still consu- ming some power. If you wish to disconnect your player completely from the mains, withdraw the plug from the AC Outlet.

Caution

Only qualified service personnel should remove the cover or attempt to service this device.

INFRA RED REMOTE CONTROL

LOADING THE BATTERIES

1Open the battery compartment cover.

2Insert two 'AAA' (R03) batteries as indicated inside the battery compartment.

3Close the cover.

Caution

Do not mix old and new batteries. AND never mix diffe- rent types of batteries (standard, alkaline and so on).

OPERATION

NOTE

-Unless otherwise mentioned, all operations can be carried out with the remote control. Always point the remote con- trol directly at the player, making sure there are no obstruc- tions in the path of the infrared beam.

-When there are corresponding keys on the front panel, they can also be used.

SWITCHING ON

1Switch on the TV and select the video input for your DVD- Video player.

2To enjoy sound through your stereo system, turn on the system and select the source input for the DVD-Video player.

OR

To enjoy DVD-Video with multichannel (surround) sound, switch on the Home Cinema system and select the source input for your DVD-Video player.

3On the front of the DVD-Video player, press Power ON/OFF. The player display lights, and the OSD invites you to load a disc.

4With Autoplay ON (the factory setting) any disc already loaded in the player starts to play.

inse

NTSC/PAL SETTING

You can switch the NTSC/PAL setting of the DVD player to match the video signal of your TV. This setting only affects the television’s on-screen display that shows the stop and setup modes. You may select either NTSC or PAL. To change the DVD player setting to PAL or NTSC, follow the step below.

1Press POWER ON/OFF button on the front panel of the DVD player to turn OFF the DVD player.

2Press and hold / and P on the front of the DVD player. While holding / and P, press POWER ON/OFF to turn ON the DVD player.

3After PAL or NTSC appears on the display panel of the DVD player, release / and P at the same time. The PAL or NTSC that appears on the display panel indicates the current setting.

4To change the setting, press P within 3 seconds. The new setting (PAL or NTSC) will appear on the display panel.

e n g l i s h 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Toll Free Help Line Model No Serial No Prevent operating and maintenance problemsNever Make or Change Connections with the Power Switched on Laser SafetyIndex Lappareil répond aux normes FCC, Part 15 et 21 CFR Set complies with the FCC-Rules, Part 15 and with 21 CFRSafety Instructions Read before operating equipment Please contact Philips at French Speaking English Speaking Your warranty does not coverModel # Serial # Contents Introduction PlacementIntroduction UnpackingRear of Player Front of PlayerRemote Control InstallationDisplay General Note Standard ConnectionsHighest Quality A/V Connection Excellent A/V ConnectionAnalog Dolby PRO Logic Multichannel Sound Digital Audio Stereo Sound ConnectionStandard Connections Getting Started Loading a Disc Getting Started Playing a DVD-VIDEO DiscPlaying a DVD-VIDEO Disc Moving to Another Chapter Playing a TitleMoving to Another Title Parental ControlSearch Still Picture and Step FrameSlow Motion Repeat CHAPTER/TITLE/DISCPlaying a Video CD Playing a DVD-VIDEO Disc Playing a Video CDPlaying a Disc When you see the Resume icon on the screen , press 2 againMoving to Another Track Moving to Another IndexRepeat TRACK/DISC Or icon appearsTo return to 4x normal speed, press down K or J again Playing AN Audio CD Playing AN Audio CDTo end the search, press 2, , or 9 as desired To go directly to 8x normal speed, hold down K or J untilCompiling AN FTS Program Favorite Track Selection FTSPlaying FTS Settings SettingsExit Settings menu, press Return or Setup This is described separately under ‘Parental Control’Parental Control Parental ControlActivating Parental Control Press or to change Parental Control to ActiveBefore Requesting Service Before Requesting ServiceCleaning Discs Optical READ-OUT System Specifications
Top Page Image Contents