Philips DVD940 Connecting the power cord, Remote control battery installation, NTSC/PAL Settings

Page 18

TV

C

B A

DIGITAL AUDIO OUT

PCM/MPEG2/AC3/DTS

L

1

MAINS

R

 

2

 

 

 

 

 

 

 

 

 

 

 

CVBS

S-VIDEO

CR

CB

Y

 

2

1

 

 

 

 

OPTICAL

COAXIAL

AUDIO

VIDEO OUT

 

 

 

Connecting to an amplifier equipped with Dolby Surround™

Dolby Surround sound

1Connect the player to the TV, then connect the player’s audio Left and Right out jacks to the corresponding in jacks on the Dolby Surround™ Audio/Video receiver, using the audio/video cable supplied (C).

If your amplifier is equipped with a Dolby Digital™ decoder,

Connect the player as described in ‘Connecting to an A/V receiver with multi-channel decoder’.

If your TV is equipped with a Dolby Surround™ decoder,

Connect the player to the TV as described in ‘Connecting to a TV’.

Connecting the power cord

1Plug the female end of the supplied power cord into the Mains jack on the rear of the player.

2Connect the other end of the cord to an AC outlet.

Note: When the player is in the “STANDBY” mode, it is still consuming some power. If you wish to disconnect your player completely from the power, unplug the power cord from the AC outlet.

Caution: Only qualified service personnel should remove the cover or attempt to service this device.

Remote control battery installation

Loading the batteries

1Open the battery compartment cover.

2Insert two 'AA' batteries as indicated inside the battery compartment.

3Close the cover.

Caution: Do not mix old and new batteries. Never mix different types of batteries (standard, alkaline, etc.)

NTSC/PAL Settings

You can switch the NTSC/PAL setting of the DVD player to match the video signal of your TV.This setting only affects the television’s on-screen display that shows the stop and setup modes.You may select either NTSC or PAL.To change the DVD player setting to PAL or NTSC, follow the steps below.

1Unplug the DVD player from the mains.

2Press and hold 9 and T on the front of the DVD player.While holding 9 and T, plug in the mains.

3After PAL or NTSC appears on the display panel of the DVD player, release 9 and T at the same time.The PAL or NTSC that appears on the display panel indicates the current setting.

4To change the setting, press T within three seconds.The new setting (PAL or NTSC) will appear on the display panel.

18 PREPARATION

Image 18
Contents Toll Free Help Line Dear Philips product owner For Customer UseIndex Region code for this set isAviso Use only with a cart, stand, tripod Read before operating equipmentLimited Warranty Contents Introduction IntroductionEntertainment for the new millennium Digital videoVideo CD PlacementUnpacking Audio CDFunctional overview Front panelRear panel Display Prog + Remote controlDVD/TV switch VOL +Menu bar/Status window Default screenOn screen display information Status window iconsTemporary Feedback Field icons Preparation General notesConnect to a TV Connecting to optional equipment Digital Multi-channel soundNTSC/PAL Settings Connecting the power cordRemote control battery installation Connecting to an amplifier equipped with Dolby SurroundAbout this manual Remote control operationGeneral explanation Menu bar operationGeneral Turning On the powerInitial Setup OperationTV Shape Personal preferencesGeneral operation CountryLow power Standby Night ModeFeatures Access Control Sound Digital outputAuthorizing discs Access control child lock DVD and VCDActivating/deactivating the child lock Deauthorizing discsAccess control Parental control DVD- Video only Activating/Deactivating Parental ControlCountry Changing the 4-digit code Parental Control DisclaimerPlaying a DVD-video disc OperationLoading discs Playing a titlePlaying a disc General featuresPlaying a Video CD Moving to another title/TRACKSearch Slow MotionStill Picture and Frame-by-frame playback RepeatShuffle Repeat A-BScan Time searchFTS-Video Special DVD-features Playback Control PBC Special VCD-FeaturesPlaying an audio CD PauseRepeat track/disc Storing an FTS Program Switching FTS ON/OFFFTS Program Erasing a track from an FTS ProgramBefore requesting service Cleaning discs Specifications Optical Readout System