Programming Your Remote Control, About Batteries

1Red Indicator Light

The Red Indicator Light blinks to show that the remote con- trol is working and also pro- vides feed back during pro- gramming sequences.

2Component Keys

Press TV,VCR or CBL once to select a home entertain- ment component to control.

3CH Keys

Use CH+ (or CH-) to select the next higher (or lower) channel for the selected home entertainment component.

4VOL Keys

Use VOL+ (or VOL-) to raise (or lower) the sound volume.

5POWER Key

Press POWER once to turn on or off the selected home entertainment component.

6MUTE Key

Press MUTE once to turn sound off or on.

7LAST Key

Press LAST once to recall the last channel.

9Keypad

Use the keypad (0-9)to directly enter in channels (for example, 09 or 31). The key- pad is also used for all pro- gramming sequences, such as entering in your programming codes.

10SLEEP Key

Press SLEEP to activate your TV’s internal sleep timer (not available for all TVs) or to pro- gram timer.

11ENTER

Use ENTER once after entering channel numbers on some TV models.

12VCR Transport Keys

Use the VCR Transport Keys to control your VCR. Press REC twice to record a tape.

13TV/VCR

Press TV/VCR once to view VCR playback or TV through the VCR.

14SCAN Key

Press SCAN once to change channels every 3 seconds. Press it again to stop the scan.

Replacement and Code Saver

When the batteries need replacing the remote control will stop work- ing and will require two (2) new "AA" alkaline batteries for continued operation. Once you remove the old batteries, program settings and codes will be saved for 10 minutes, allowing adequate time to insert new ones.

However, if you do not replace the batteries within the allotted time (e.g., 10 minutes), you will have to reprogram the remote control.

PROGRAMMING YOUR REMOTE CONTROL

Philips/Magnavox Components

The remote control can control up to three different components and is already pre-programmed for use with newer Philips/Magnavox audio/video equipment. Unless you want to change a factory setting, skip the programming instructions and simply start using your new remote control.

Programming Other Components

To control component brands other than Philips/Magnavox, you’ll need to perform the following steps to manually program the remote with codes listed under Manufacturer’s Codes on pages 23 through 28. Or as an alternative, you can use the Auto Scan feature, on page 5, to pro- gram your component codes.

The following chart lists the remote component keys and what type of device each key will control:

Key	Programmed to Control
TV	TV

8SET Key

Use SET for all programming sequences.

SETTING UP YOUR REMOTE CONTROL

Before using your new remote control, you will need to obtain and install new batteries, as described on the next page. Then you’ll also need to program the remote control with the correct code numbers for your specific components. See instructions starting on page 4.

ABOUT BATTERIES

Note: The remote requires two (2) new "AA" alkaline batteries (not supplied). Do not mix old and new batteries or mix alkaline with man- ganese-type batteries.

Installing Batteries

VCR	VCR
CBL	Cable Box

IMPORTANT: Please completely read and review the following steps before proceeding. We recommend highlighting the codes (start- ing on page 23), for the brands you wish to program or writing them down in the supplied chart.

Setup Codes for My components

TV	___	___	___	___
VCR	___	___	___	___
CBL	___	___	___	___

To Manually Program the Remote Control:

1.	Manually turn on a component (e.g.,TV,VCR, etc.) and, if
	applicable, insert media (e. g., cassette).

Battery Saver

1.On the back of the remote control, push the tab and lift the battery com- partment cover off.

2.Match the + and – marks on the batteries to the + and – marks in the battery case and insert two (2) "AA" alkaline batteries.

3.Press the battery cover back into place. The tab should click when the cover is locked.

4.Test the unit by pressing POWER and any Component key (e.g., TV, VCR, CBL). If the batteries are inserted correctly the red indicator light will blink once.

2.	On the remote control, press a component key once
	(e.g., TV,VCR,CBL).
3.	Press and hold SET (approximately 5 seconds) until the
	red light blinks twice, then release SET.
4.	Enter the first four-digit code for your brand of compo-
	nent. If performed correctly, the red light will blink
	twice.
5.	Aim the remote control at the component and press
	POWER ONCE. It should turn off. If it does not
	respond, repeat steps 2 and 3, trying each code for your
	brand until you find one that works. If it still does not
	work, try using Auto Scan (see below) on how to pro-
	gram your component.
6.	Repeat steps 1 through 5 for each component you want
	to program into the remote control.

NOTES: Press each key within 10 seconds of the previous entry. Otherwise, the remote control will exit the programming mode.

The remote has a Time Out feature that will automatically deactivate the remote control if a key is depressed for more than 30 seconds. This feature will help conserve the battery life should your remote control get stuck in a place where keys remain depressed (e.g., between the sofa cushions).

If you press SET at any time (except during step 3), the remote con- trol will exit the programming mode without saving your entries. You will have to start with step 1 to begin programming again.