Philips DLP HDTV setup guide Operating the TV, Using the OSD menu

Operating the TV

Remote control buttons Inserting remote control batteries

Using the TV buttons

Info

Dash key

MTS

INFO

IR filter

Power

Channel number

keys Recall

1. The battery cover is on the

back of the remote control.

Slide the battery cover in the

direction of the arrow to

remove it.

Volume up/down

-

Channel up/down Closed Captions

OK

Arrow keys

2. Insert the two AAA batteries

provided in the package, with

the polarity of the batteries

MAGNAVOX

Mute		MENU	OSD menu
Source shortcut
keys
Smart Picture	SOUND		Picture size
			Electronic
Smart Sound
	PIP SIZE		program guide
Source selection	PIP/PBP		Sleep
PIP/PBP buttons			Freeze picture

matching the image in the

battery compartment.

3. Slide the battery cover in the

direction of the arrow until it

clicks and is secure.

1 2 3 4 5

1.Press to view or exit from the OSD menu.

2.Press to skip to the previous or next channel.

3.Press to increase or decrease the volume.

4.Press to select an input source or confirm selection of a menu item.

5.Press to turn power on or off.

Turning on the TV

To switch on the TV:

1.Connect the power cord to the TV as illustrated.

2.Plug the cord into a wall outlet.

3.Switch on the main power switch located at the left side of the display.

4.Press the power button on the front panel or remote control to turn on the TV. The TV will turn on after warming up for approximately

30 seconds.

Power switch

Note:

If the remote control and control panel do not work, ensure that the power switch on the rear of the TV is set to ON.

Turning off the TV

To switch the TV off:

Press the power button on the front panel or remote control to turn off the TV. The screen turns blank immediately but it will take approximately one minute to cool down and then shut down the whole system.

Except in case of emergency, it is not recommended to use the main power switch to switch off the system. The lamp life may be severely reduced if the system is not allowed to cool down properly by abruptly shutting down the system using the main power switch.

Power switch

Selecting the source

After switching on the TV, select the appropriate input source using the front panel buttons or the remote control as follows:

•Press ATV, DVI/HDMI, YPbPr, DTV, AV, SV, or VGA on the remote control to switch to the respective input.

•Press the ENTER/SOURCE button on the front panel of the TV repeatedly to switch through all the input sources.

•Press SOURCE on the remote control to select the source from the on-screen menu. A list of input sources is displayed on the screen. Select the appropriate input using the cursor keys and press OK on the remote control to display the input signal.

Input Select

EXIT

ATSC

Analog TV

AV1

AV2

AV3

AV4

HDMI

VGA

Front

Using the OSD menu

The On-Screen Display (OSD) menus enable you to customize the TV’s audio, video, and other settings according to your preferences.

Press the MENU button on the front panel or the remote control to view the OSD menu.

-Use the cursor keys to navigate through the menu items.

-Press OK to select an option.

-Press the MENU button again to exit from the menu.

Main Menu

Picture	Smart Picture	Personal Dynamic Natural Cinema
Sound	Brightness	50
Size	Contrast	50
PIP/PBP	Sharpness	7
Parental Control	Temp.	Warm Normal Cool
Channel Setup	Tint	50
Setup	Saturation	50
Exit	Back

Setting the language Setting the tuner mode

Scanning channels

The setup menu provides various options to customize the TV’s settings. Select the Language option from the menu and use the cursor keys to select the desired OSD language.

Main Menu

Picture	OSD Hold Time		5s	10s	15s	20s		25s	30s
Sound	Language		English		Español			Français
Size	Sleep	Timer	Off	15m 30m		60m 90m
PIP/PBP	Closed	Caption	Press		Right		to	Enter
Parental Control	Time Zone		Atlantic		Eastern		Central		Mountain
Channel Setup			Pacific		Alaska		Hawaii
Setup	Daylight Saving		Off	On
Exit	Back

The channel setup menu helps you to configure and set up channels. Select the Tuner Mode option and use the cursor keys to select antenna or cable input for the tuner.

Main Menu

Picture	Tuner Mode	Antenna	Cable
Sound	Channel Search		Press	right
Size	Manual Search		30
PIP/PBP	Favorite Channel	Edit	Press	right
Parental Control	Reset Channel
Channel Setup	Back
Setup
Exit

The channel setup also has the auto-scanning option that enables you to scan for channels. Use this option to start scanning for channels automatically as follows:

1.Select the Channel Search item from the channel setup menu and press right cursor to start scanning for channels automatically. Scanning begins.

2.Press OK at any time to stop scanning.

Auto Scanning	Auto Scanning
Antenna	Cable
RF Channel: 11	RF Channel: 11
Major Number: 2	RF Channel: 11
Analog signal scan	Digital signal scan

Copyright 2005. All rights reserved.