Philips DCR 9001/22 user manual Insert the two batteries supplied in your remote control

Page 7

- Insert the two batteries supplied in your remote control.

Batteries are removable from the remote using common household tools. The batteries supplied do not contain hazardous substances such as Mercury, Cadmium, or Lead. However, they must not be disposed of with your household waste but to a local separate battery collection system.

-Switch on your TV set and select the appropriate HDMI input (refer to your TV set user manual).

-Now plug the receiver's power supply cord into the mains. The receiver display

indicates , then .

-Press V-Outputonce. The receiver display should indicate

If

is displayed instead, proceed to chapter 8.

- Check that the welcome screen displays on the TV screen.

If no picture is displayed or the picture quality is poor, refer to section

Troubleshooting.

-Press P+ then P-. Wait for a few seconds for the First installation screen to appear.

-Select your favourite language.

-Check for adequate signal strength and quality.

-Press OK to start searching for channels. During the search, a bargraph indicates the channel search progress. This may take some time. It is to ensure the receiver will not miss out on channels.

Once the scan has been successfully completed, a completion message is displayed. - Press OK.

A new screen appears, with a message indicating that a search for new, upgraded software is in progress:

-Either wait for software detection, and then proceed as indicated on screen. It is recommended to accept software so as to keep your receiver up-to-date.

-Or press EXIT to stop searching for new software.

At the end of first installation, your receiver tunes to the first channel in the main TV list.

For detailed information on first installation, see chapter 8.

For detailed information on other connections, refer to the on-screen help,

either by pressing the yellow colour key or via the menu by selecting the Help item. Alternatively, see chapter 7.

Your remote control is set to perform volume control through a Philips TV set. If you have a TV set other than Philips, refer to paragraph 15.3 to adapt the brand setting of your remote control to your TV set.

EN

55

Image 7
Contents DE Benutzerhandbuch Foreword Contents Premiere Menu SettingsAdvanced settings Menu systemUnpacking TV set Quick installationInsert the two batteries supplied in your remote control So do not dispose of them with your normal household waste Meaning of symbolsSafety instructions EN 4.1 Front panel Product descriptionPictograms Front panel displayDescription of segment display messages U I O Rear panelInserting your Smartcard RED, GREEN,YELLOW Blue Using your remote control when the STB mode is selectedDigital connection to TV via Hdmi lead supplied recommended Connecting your digital receiverConnections Your TV set is Hdtv capable HD-Ready labelTV set Connection to a recorder Analogue connection to TV via YPbPr lead not suppliedYour TV set is only Sdtv capable Digital audio connections Connecting to a video projector to watch Digital TVYour video projector is only Sdtv capable Search failure First installationInstallation settings Channel searchDay-to-day operation Switching your receiver on Or to LOW Power or STAND-BYUsing number keys of the remote control Using channel listsPIN code Volume control / +Banner Electronic Programme Guide EPG Set or delete recording timersViewing teletext Checking or changing the video output resolution settingSetting a timer in the EPG Cancelling an active timerPremiere Multifeed Premiere featuresEN 11.1 Menu tree Premiere MenuEXT1 Scart Basics Changing settingsCancelling/storing changes Menu navigationSmartcard Software UpgradeFactory Settings PIN Code ChangeWake up ScanDisplay Dolby Digital out of the digital audio outputTo set or edit a timer SettingsTimer Manager To delete an existing timerRemove/Reorder Channels List OrganizationList Editing Channel PoolScan Language options SettingsFor Parents Display optionsBroadcast is Advanced settingsTV Settings Case1TV is System SettingsTime Settings TV is 169 Any settingSystem Information Software UpgradeSoftware upgrade messages Decoder StatusPage Connecting your equipment for Video/DVD Recorder Control Advanced settingsRestoring factory settings Changing the remote control settingRecording using the Video/DVD Recorder Control feature Digital receiver and VCR or DVD recorder settingsChanging the volume and mute control assignment Mode selection selecting the device you want to controlVolume and mute control assignment Default volume and mute control assignmentDisclaimer Battery changeSTB Controlling your TV,Video Recorder, DVD and amplifier Using the remote control when the TV mode is selectedTV/VCR Using the remote control when the VCR mode is selectedUsing the remote control when the DVD mode is selected Preset Up/Down Tuning Down/Up Glossary Symptom Cause Remedy TroubleshootingRemedy Symptom Cause73/23/EEC 93/68/EEC 89/336/EEC Technical specificationsPage Code List für verschieden Marken/Brand code list BPL AGBART ASA100 101 102 103 KEC 104AVP GPX105 106 107 108 TSM 109XMS 110 111 3111 176