Switching on and initial setup
Before you switch on the TV, check that the AC power cord is properly connected. Press . POWER at the right side of the TV, or press
After you read a welcome screen, follow the
|
| Select your menu | English |
|
|
|
| ||
|
| |||
|
| language with the |
| |
|
|
|
| |
|
| Up/Down buttons on | Français |
|
|
| your remote control, | Español |
|
|
| press the OK button to |
| |
|
| proceed. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Network setup screen will appear. Use Î⁜/ï/Í⁜/Æ to select [Next] > [Wireless] / [Wired], then press OK.
•If you select [Wireless], use Î⁜/ï to select a setting and then press OK.
Setting items | Description | |
| Select this setting if your router has a | |
| Protected Setup (WPS) button. Start scanning | |
Easy connect | for wireless networks on the TV after pressing | |
the WPS button on your router. If connection | ||
| ||
| test fails, refer to the router's manual for more | |
| details. | |
| Search for wireless networks automatically | |
Scan | and select the wireless network name (SSID) | |
from the list. see ‘Wireless network setting | ||
| ||
| (Auto)’on page 30. |
•If you select [Wired], use Î⁜/ï to select a setting and then press OK.
Connection test will start automatically. (See ‘Connection test’ on page 30.) Press Î⁜/ï to select the desired mode for energy saving, then press OK.
|
| "Home" is recommended for | Retail store |
|
|
|
| ||
|
| |||
|
| normal home use.In the Retail |
| |
|
|
|
| |
|
| Store mode all settings are | Home |
|
|
| fixed. |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Select [Retail store] if you want backlight to be brighter. Select [Home] to reduce power consumption.
You must set [Home]. Otherwise, personalized picture and sound settings will not be memorized after the unit goes to standby mode.
•Select [Retail store], the unit will be set up with predefined setting for retail displays.
•Select [Home], the unit will be set to maximize energy efficiency. Picture and sound settings can be adjusted and saved as per your personal preferences.
Press Í⁜/Æ to select [⁜Start], then press OK to begin [⁜Settings assistant].
Settings assistant will allow you to customize your picture settings to your personal preference. You will see a series of test pictures where the right side and left side differ. Select the side that is most pleasing to you with the Left/Right buttons.
Cancel Start
Select [⁜Picture A] or [⁜Picture B] by pressing Í⁜/Æ that is the most pleasing to you, then press OK.You see 5 different pictures to be completed.
Which side of the picture do you prefer?
Cancel | Picture A | Picture B |
Press Í⁜/Æ to select [⁜Store], then press OK.
Store your preferences.
Cancel Store
Press OK to finish [⁜Settings assistant].
The TV has learned your preferences.
Exit
Press Í⁜/Æ to select [⁜Finish], then press OK.
Finish the Setup.
Note
••If you are not receiving a signal from your cable service, contact the CATV provider.
••If you press . during autoprogram, an installation will be canceled except the language selection.
••The initial autoprogram function can be executed for either [Antenna] or [Cable] only once. When you change the connection (Antenna / Cable), set autoprogram again. (Refer to page 35.)
English
EN 11