Philips TP2784C1 manual Using the AUDIO/VIDEO Input Jacks, Connect the Video yellow

Page 31

USING THE AUDIO/VIDEO INPUT JACKS

AUDIO/VIDEO INPUTS

The TV’s Audio/Video Input jacks are for direct picture and sound connections between the TV and a VCR (or similar device) that has Audio/Video Output jacks.

BEGIN

Connect the VIDEO (yellow)

CABLE to the VIDEO IN-1 jack on the back of the TV. Then con- nect the AUDIO (red and white) CABLES to the AUDIO (left and right) IN-1 jacks on the rear of the TV.

Connect the VIDEO (yellow)

CABLE to the VIDEO OUT jack on the back of the VCR. Then connect the AUDIO (red and white) CABLES to the AUDIO (left and right) OUT jacks on the rear of the VCR.

Turn the VCR and the TV ON.

Use the AV button on the remote to select the AV 1 chan- nel.

With the VCR ON and a prere- corded tape inserted, press the PLAY button to view the tape on the television.

NOTE: Repeatedly pressing the AV button on the remote will toggle the picture source from the current chan- nel, to the last channel viewed, then to the AV 1 connection, then to the AV 2 connection.

This also applies to the Multi Media button on the remote. Repeatedly pressing the Multi Media button will toggle the picture source from the current channel, to the last viewed channel, then to the MM 1 (AV 1) connection, then to the MM 2 (AV 2) connection.

24

AV 1

AV 2

4

POWER

SLEEP

TV	AV	ON/OFF	POSITION	FREEZE
VCR	SWAP	SOURCE	PIP CH
			UP	DN

ACC

SMARTSMART

SOUNDPICTURE

MENUSURF

VOL			CH
	MUTE
CC	STATUS	CLOCK	A/CH
	EXIT	TV/VCR
VCR			MULTI
RECORD	INCREDIBLE		MEDIA
	INCREDIBLE

STEREO

When using the Audio/Video IN-1input jacks, the video and sound can be viewed and heard on the AV 1 channel.

When using the Audio/Video IN-2input jacks, the video and sound can be viewed and heard on the AV 2 channel.

BACK OF TV

1

	S-VIDEO
	VIDEO
	L
ANT "A"	AUDIO
75	R/MONO

IN-1OUT

VIDEO IN (YELLOW)

AUDIO IN	2
(RED/WHITE)	2
OUT	OUT ANTENNA
	IN

BACK OF VCR

R AUDIO L	VIDEO ANTENNA
	OUT
IN	IN

3

VCR

(EQUIPPED WITH VIDEO AND

AUDIO OUTPUT JACKS)

IF YOU ARE USING A

NON-STEREO DEVICE,

USE ONLY THE AUDIO

R/MONO JACK.

31

Image 31

Contents

TP2784C1 Warranty Verification Safety Instructions Read before operating equipment Table of Contents Cable/Antenna FeaturesPress the STATUS/EXIT button Adjusting the TV PicturePress the Numbered buttons Setting the TV’S ClockActivating the TV’S on Timer Control Press the STATUS/EXIT button Selecting the TV’S on Timer ChannelStart up time. Refer to page 8 for Further details Setting the TV’S on Timer Start TimeUse the Cursor UP or CUR SOR Down buttons to set AM orTurning on the on Timer Display Movie Ratings Understanding SmartlockEnter current access code Using Smartlock Setting UP the Access CodePress the Channel + or Using Smartlock Blocking ChannelsPress the STATUS/EXIT but- ton to remove the menu Using Smartlock Movie RatingUsing Smartlock TV Rating Options Using Smartlock BlockingUsing Smartlock Block Unrated Using Smartlock no Rating Example Blocking is set to OFF Reviewing the Smartlock SettingsViewing Blocked Programming Interference and improve Quality of the picture Turning on the Noise Reduction ControlContrast + option area Turn the Contrast + feature on Or OFFTurning on the Contrast + Control Trast + controlMode Using the Closed Caption ControlGood BYE Sleep Using the Sleep Timer ControlBalance may all be used to Adjust the sound playback of TV Adjusting the Treble , Bass , and Balance Sound ControlsPrograms Placed in the Stereo mode, the sound com Setting the TV for Stereo and SAP Programs Remember, if stereo is not present On a selected show and the TV isPress the Volume + or but Using the Incredible Stereo ControlUsing the Volume BAR Control Press the Volume + orUse the Cursor Left or Right buttons to set Setting the Audio OUT ControlUsing the TV Speaker Control and Audio Output Jacks Connect the Video yellow Using the AUDIO/VIDEO Input JacksConnect the S-VIDEO Using the AUDIO/VIDEO Input Jacks CONT’DButton repeatedly to select either Press the Smart PicturePress the Smart Sound but Using the Smartsound ControlEMPTY, Press to add Press the Channel + orPress the Surf button on Read, the Surf List isFind your Three-Digit Code on pages Setting the Remote Control to Operate Accessory DevicesRemote control number for your Place the TV/VCR/ACCEnter the THREE-DIGIT Place the TV/VCR/ACCPress the VCR Record Press the Smart SoundSearch Method Turn on the device by press- ing the Power button onRemote VCR Code no Remote Control Direct Entry CodesRemote Dvdcode no Rewind Button Using the REMOTE’S VCR ButtonsMove to the next page after Connect the Video OUTAlso connect the Audio OUT Right and Left jacks fromAV 1, AV 2, SVID-R for picture Turn the TV and VCR orPress the PIP ON/OFF but Press the PIP Source butUsing the PIP PICTURE-IN-PICTURE Feature Remember, although Adjusting the PIP Color and TintConnect the Cable OUT on First use an optional signalConnect the Video OUT jack Connect a second yellow Video First connect the original cableConnect the ANT OUT jack on Connect the yellow VideoTips if Something Isnt Working TV Displays Wrong Channel or No Channels AboveIndex Glossary to Television TermsPhilips Consumer Electronics Company Texas Limited Warranty