Philips TP2784C1 manual Search Method, Turn on the device by press- ing the Power button on

Page 38

SETTING THE REMOTE CONTROL TO OPERATE ACCESSORY DEVICES

Search Method

Your TV remote can be set to work various accessory

devices such as VCRs, Cable Boxes, Satellite Receivers, DBS, DVD, etc. by using the search method.

If the Direct Access method shown on page 37 did not set your remote to work your acces- sory device, follow the easy steps listed below.

Please read steps 1-4 before beginning.

BEGIN

Turn ON the device by press- ing the POWER button on the

device you are attempting to pro- gram.

Place the TV/VCR/ACC

Mode Switch in the proper posi-

tion.

Press and hold the VCR RECORD and the SMART SOUND buttons simultaneous- ly.

The device will begin to change channels after the remote identifies the correct code. When the channels start to change, release the VCR RECORD and SMART SOUND buttons. The remote should be ready to oper- ate the device.

SMART HELP

This method can take up to two minutes to perform.

Don’t let the device change more than five channels after the remote identifies the code. If you do, the remote may pass up the right code; another two minute search cycle will have to be repeated.

If no channel change happens within two minutes, repeat steps 1-4. Should a channel change still not occur, the remote will not work the desired device.

Satellite Receiver,
DBS, DVD,
or similar device
Cable Converter		070809 06	07
1			07
1			0809
		06	0809
		0708
VCR		09
VCR
2	SLEEP	POWER	4
	SLEEP	POWER	4
TV	AV	ON/OFF POSITION FREEZE

VCR SWAP

SOURCE

PIP CH

UP DN

ACC

SMARTSMART

SOUNDPICTURE

MENUSURF

3

VOL			CH
	MUTE
CC	STATUS	CLOCK	A/CH
	EXIT	TV/VCR
VCR			MULTI
RECORD	INCREDIBLE		MEDIA
	INCREDIBLE

3

38

Image 38

Contents TP2784C1 Warranty Verification Safety Instructions Read before operating equipment Table of Contents Features Cable/AntennaAdjusting the TV Picture Press the STATUS/EXIT buttonSetting the TV’S Clock Press the Numbered buttonsActivating the TV’S on Timer Control Selecting the TV’S on Timer Channel Press the STATUS/EXIT buttonSOR Down buttons to set AM or Setting the TV’S on Timer Start TimeUse the Cursor UP or CUR Start up time. Refer to page 8 for Further detailsTurning on the on Timer Display Understanding Smartlock Movie RatingsUsing Smartlock Setting UP the Access Code Enter current access codeUsing Smartlock Blocking Channels Press the Channel + orUsing Smartlock Movie Rating Press the STATUS/EXIT but- ton to remove the menuUsing Smartlock TV Rating Using Smartlock Blocking OptionsUsing Smartlock Block Unrated Using Smartlock no Rating Reviewing the Smartlock Settings Example Blocking is set to OFFViewing Blocked Programming Turning on the Noise Reduction Control Interference and improve Quality of the pictureTrast + control Turn the Contrast + feature on Or OFFTurning on the Contrast + Control Contrast + option areaUsing the Closed Caption Control ModeUsing the Sleep Timer Control Good BYE SleepPrograms Adjusting the Treble , Bass , and Balance Sound ControlsBalance may all be used to Adjust the sound playback of TV On a selected show and the TV is Setting the TV for Stereo and SAP ProgramsRemember, if stereo is not present Placed in the Stereo mode, the sound comPress the Volume + or Using the Incredible Stereo ControlUsing the Volume BAR Control Press the Volume + or butSetting the Audio OUT Control Use the Cursor Left or Right buttons to setUsing the TV Speaker Control and Audio Output Jacks Using the AUDIO/VIDEO Input Jacks Connect the Video yellowUsing the AUDIO/VIDEO Input Jacks CONT’D Connect the S-VIDEOPress the Smart Picture Button repeatedly to select eitherUsing the Smartsound Control Press the Smart Sound butRead, the Surf List is Press the Channel + orPress the Surf button on EMPTY, Press to addPlace the TV/VCR/ACC Setting the Remote Control to Operate Accessory DevicesRemote control number for your Find your Three-Digit Code on pagesPress the Smart Sound Place the TV/VCR/ACCPress the VCR Record Enter the THREE-DIGITTurn on the device by press- ing the Power button on Search MethodRemote Control Direct Entry Codes Remote VCR Code noRemote Dvdcode no Using the REMOTE’S VCR Buttons Rewind ButtonRight and Left jacks from Connect the Video OUTAlso connect the Audio OUT Move to the next page afterPress the PIP Source but Turn the TV and VCR orPress the PIP ON/OFF but AV 1, AV 2, SVID-R for pictureUsing the PIP PICTURE-IN-PICTURE Feature Adjusting the PIP Color and Tint Remember, althoughConnect the Video OUT jack First use an optional signalConnect the Cable OUT on Connect the yellow Video First connect the original cableConnect the ANT OUT jack on Connect a second yellow VideoTV Displays Wrong Channel or No Channels Above Tips if Something Isnt WorkingGlossary to Television Terms IndexPhilips Consumer Electronics Company Texas Limited Warranty