ANTENNA
CABLE |
| CABLE OR ANTENNA |
|
| |
| OUTPUT | 75 |
| 2 | |
IN | /OUT | |
(TO TV) |
|
3
Cable box
ANTENNA
HDMI2 HDMI1 | VGA | L | Y | Pb | Pr | L | R | AV1 |
VIDEO |
|
|
|
|
| |||
|
| IN |
|
|
|
|
|
|
| PC IN | R |
|
|
|
|
|
|
| Y | Pb | Pr | L | R | AV2 | ||
|
|
|
|
|
|
|
| |
CABLE |
| AV3 |
|
|
|
|
|
|
1 | CABLE OR ANTENNA |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 75 | 4 | AV3: |
|
|
|
|
|
| 2 |
|
|
|
|
| ||
|
| L+R+VIDEO |
|
|
|
| ||
SPLITTER |
|
|
|
|
|
|
|
|
3
IN OUT
Cable box
Watching cable TV programs that don’t require the use of a cable box.
Since you’ve connected the cable TV signal directly to the TV’s tuner, you can also watch unscrambled programs by simply tuning to
the desired channel; however, you must first use Auto program to store available channels in the TV’s memory. (p. 12)
Note: This connection will supply stereo sound to the TV if the station you are viewing broadcasts stereo sound.
- Cable TV
Connect the cable TV signal to the CABLE/
ANTENNA 75 
jack at the bottom of the TV. See page 12 for details on using Autoprogram to store channels in the TV’s memory.
Note: This connection will supply stereo sound to the TV if the station you are viewing broadcasts stereo sound.
- Cable box with RF IN/OUT
•Connect the incoming cable TV signal to the cable IN jack 
on the back of the cable box.
•Connect a coaxial cable (not supplied) from the TO TV jack on the back of the cable box to the CABLE/
ANTENNA 75 
jack 
at the bottom of the TV. Note: Your cable box may have a different label for the TO TV jack. Commonly used labels include OUTPUT or OUT.
•Set the OUTPUT CH switch 
on the cable box to CH 3 or 4 (whichever is correct for your cable box). Next, tune the TV to the corresponding channel. Once
tuned, change channels using the cable box, not the TV.
Note: This connection will not supply stereo sound to the TV. The reason is that the RF output on a cable box - labeled TO TV, OUT or OUTPUT for example - will not send a stereo signal to the tuner (VHF/UHF) input on a TV.
- Cable box with A/V outputs
• Connect the incoming cable TV signal 
to a signal
splitter (not supplied). The signal splitter enables you to avoid having to use the TO TV jack on the back of the cable box. This jack will not supply stereo sound to the TV.
Note: Your cable box may have a different label for the TO TV jack. Commonly used labels include OUTPUT or OUT.
•Connect a coaxial cable (not supplied) to a connector on the signal splitter and to the CABLE/ANTENNA 75
jack 
on the TV.
•Connect another coaxial cable (not supplied) to a connector on the signal splitter and to the cable IN jack 
on the back of the cable box.
•Connect A/V cables (not supplied) to the VIDEO IN and AUDIO L and R outputs on the back of the cable box and to the AV3 video (labeled VIDEO IN) and AUDIO (labeled L and R) jacks 
on the back of the TV.
•To view programs from your cable box, first press the SOURCE button on the remote control.
•Press the cursor down or up buttons until the AV3 signal source is selected.
•Press the OK button to confirm your selection. The AV3 input source becomes current for the viewing of
cable TV programs through your cable box.
Note: If your cable box audio/video outputs do not supply video and stereo audio to the TV, you will need to make the connection shown above in “Cable box with RF IN/OUT.
6