Philips 47PFL3605H Use a Conditional Access Module, Use Philips EasyLink, Access CAM services

Page 36

Use a Conditional Access Module

A Conditional Access Module (CAM) is provided by digitalTV service operators to decode digitalTV channels.

Note

Refer to the documentation from your service operator on how to insert a smart card into the Conditional Access Module.

Insert and activate a CAM

Caution

Be sure to follow the instructions described below. Wrong insertion of a CAM may damage both the CAM and your TV.

1 Switch off the TV and disconnect it from the power outlet.

2Following the directions printed on the CAM, gently insert the CAM into the COMMON INTERFACE at the side of the TV.

3Push the CAM in as far as it will go.

4Reconnect the TV to the power outlet.

5Turn on the TV and wait for the CAM to be activated. This may take several minutes. Do not remove the CAM from the slot when in use — removing the CAM will deactivate digital services.

Access CAM services

1After inserting and activating the CAM, press MENU.

2 Press to select [Setup] >

[Features] > [Common interface].

»Applications provided by the digitalTV service operator appear on the screen.

Note

This menu option is available only if the CAM is inserted and activated correctly.

Use Philips EasyLink

Your TV supports Philips EasyLink, which uses the HDMI CEC (Consumer Electronics Control) protocol. EasyLink-compliant devices that are connected through HDMI connectors can be controlled by a single remote control.

Note

The EasyLink-compliant device must be switched on and selected as the source.

Philips does not guarantee 100% interoperability with all HDMI CEC devices.

34EN

Image 36
Contents Page Clientes en España Contents Koninklijke Philips Electronics N.V.All rights reserved Compliance with EMFRefit the fuse cover CopyrightSafety Risk of short circuit or firefire Risk of injury or damage to the TV Risk of overheatingScreen care Disposal of your old product and batteriesHigh energy efficiency Low standby power Environmental effortsSide controls and indicators Remote controlYour TV Remote control usage Switch your TV on / off or to standby Switch channelsSwitch channels with the channel grid Use your TVAdjust TV volume Watch connected devicesUse the source button Access TV menus Use more of your TVRename devices from Home menu Remove devices from the home menuChange picture and sound settings Use settings assistantManually adjust picture settings Use smart pictureFollowing picture settings can be configured Change picture formatSummary of picture formats Manually adjust sound settings Use smart sound» The Sound menu appears Press Use the universal access menu Use advanced teletext FeaturesAccess the teletext options menu Select teletext subpagesSelect T.O.P. teletext broadcasts Use TeletextSelect a favourite list View all channelsSwitch on EPG Use the Electronic Programme GuideAdd a channel to a favourite list Remove a channel from a favourite listUse the TV clock Use the EPG options menuSet the TV clock manually Display the TV clockUse timers Change the clock modeAutomatically switch the TV to standby sleep timer Change the time zoneAutomatically switch the TV on on timer Use TV locksSet or change your PIN code Lock or unlock the TVEnable subtitles on analogue TV channels Use subtitlesLock or unlock one or more channels Set parental ratingsEnable subtitles on digital TV channels Select a subtitle language on digital TV channelsView photos Change slide show settings Music settingsView a slide show of your photos Listen to musicUpdate the TV software Listen to digital radio channelsUpdate using OAD Change TV preferencesPress OK Press Menu to exit Access decoder channel Reset the TV to factory settingsStart a TV demo Set decoder channelInstall channels Automatically install channelsManually install channels Select your systemFine-tune analogue channels When complete, select Store to store the frequency Rename channelsRearrange channels Test digital receptionBack connector TV Antenna Signal input from an antenna, cable or satelliteConnect devices VGA Side connector Connect a computer Hdmi cable DVI-HDMI cableHdmi cable and HDMI-DVI adaptor VGA cableUse a Conditional Access Module Access CAM servicesUse Philips EasyLink Insert and activate a CAMUse a Kensington lock Supported display resolutions PowerMultimedia Tuner / Reception TransmissionWeight 19.8 kg Supported TV mountsProduct specification Troubleshooting General TV issuesTV channel issues Picture issues Sound issuesHdmi connection issues There are problems with Hdmi devicesComputer connection issues Contact usSide connectors Care IndexPIN code Ratings lock OverviewDigital services On timer One-touch play One-touch standby Parental rating39, 31 With slideshow Mute TV speakersDisconnect USB Listen to music Update software 44 EN 45 EN Page Koninklijke Philips Electronics N.V. All rights reserved