Philips 40PFL3705D Switching on and set up the TV, Press OK to begin Settings assistant

Page 12

Switching on and set up the TV

Before you switch on the TV, check that the AC power cord is properly connected. Press .POWER at the right side of the TV, or press . on the remote control.The TV normally takes 25-30 seconds to start up and the following screen appears the first time you turn on the TV.

InitialI iti l Setupt

 

 

 

 

Select your menu language.

 

English

 

 

 

 

 

 

 

Seleccione el idioma para el menú.

 

Español

 

 

 

 

Sélectionnez la langue du menu.

 

 

 

Français

 

 

 

 

Select

OK OK

MENU

Skip

Follow the on-screen instructions to select your language and complete your TV setup. Installation takes approximately 10 minutes.

Press Í or Æ to select the desired mode for energy saving, then press OK.

InitialI iti l Setupt

Select “Retail” or “Home” for your location.

Retail

Home

Select

OK OK

SETUP

Exit

Select [Retail] if you want backlight to be brighter. Select [Home] to reduce the power consumption.

You must set [Home]. Otherwise, the settings of picture and sound quality you adjusted will not be memorized after you turn off the unit.

Select [Retail], the unit will be set up with predefined setting for retail displays. In this setting, the power consumption may possibly exceed the limited requirement of the ENERGY STAR® qualification.

Select [Home], the unit is set to maximize the energy efficiency for home setting and it can be adjusted through a choice of picture and sound quality according to your preference.

Press OK to begin [Settings assistant].

Settingstti assistanti t t

Settings assistant helps you customize picture settings. You will see a series of test pictures where the right side and left side differ. Select the side that is most pleasing to you with the Left/ Right keys.

 

BACK

Back

MENU

 

OK Next

Exit

 

 

 

 

Press Í or Æ 5 times to select the side of the pictures that is the most pleasing to you. then press OK.

E n g l i s h

Left side

 

Right side

 

 

 

1/5 Select the picturei settingi thatt t you preferf ..

Select

BACK

Back

MENU

OK Next

Exit

Press OK to finish [Settings assistant].

Settingstti assistanti t t

You have set up your viewing preferences.

 

OK Store

BACK

MENU

 

 

Back

Exit

 

 

 

 

Finish the Setup.

Note

If you are not receiving a signal from your cable service, contact the CATV provider.

If you press . or MENU during autoprogram, this setting will be canceled.

The initial autoprogram function can be executed for either [Antenna] or [Cable] only once.When you change the connection (Antenna / Cable), set autoprogram again. (Refer to page 24.)

If there is no signal input from the antenna terminal and no operation for several seconds after you turn on the TV, [Helpful Hints] appears. Follow the instructions listed on the TV screen.

EN 11

Image 12
Contents Register your product and get support at Contents Return your Product Registration Card or register online at Grounding Conductors Ground ClampsPhilips Product information Screen careEnvironmental care Regulatory noticesSide controls and indicators Remote controlYour TV Info Supplied accessories Installing the remote control batteriesGet started Standing mount the TVConnecting the antenna or cable If you connect to a DBS Direct Broadcast SatelliteANT Composite Video and Audio YPbPr Component Video InputPlugging in the AC power cord Disconnect the TV from the power outletManaging cables Switching on and set up the TV Press OK to begin Settings assistantPress OK to finish Settings assistant Finish the SetupSwitching your TV on / off or to standby Switching channelsUse your TV This section helps you perform basic TV operationsAdjusting volume Still modeWatching channels from a set-top box Watching connected devicesSwitching audio mode Watching a Blu-ray DiscChanging picture and sound settings Changing picture settingsSummary of picture settings Changing auto picture modeChanging picture format Summary of picture formatsNormal Display a 169 picture at its original size Using your TV as a PC monitor Supported screen resolutionsChanging sound settings Summary of sound settingsSleeptimer Child and rating locksUsing the movie ratings lock Summary of TV ratingsSummary of US movie ratings Summary of Canadian English ratingClosed caption Energy saving mode EasyLinkSet your location to home Press Î or ï to select the desired mode, then press OKConnect a USB storage device View your pictures on a USB deviceDisconnect a USB storage device JpegConfigure how the slideshow is played Listen to music on a USB deviceInstall channels Press Menu on the remote control and select LanguagePress OK to start the installation Selecting your menu languageOptimizing the signal quality from your antenna Channel listAdd channels Upgrade your TV software Preparing for the software upgradeUpgrading software Checking your current software versionHdmi 3 input jack Third Hdmi in connector USB Connect devicesConnection overview Component video and audio input jackSelecting your connection quality Video Good qualityHdmi Highest quality Component Y Pb Pr High qualityConnecting your devices Connecting a digital home theater amplifier If you connect a PC with an S-Video connector at the sideIf you connect a PC with a DVI connector If you connect a PC with an Hdmi connectorTroubleshooting Downloading an electronic copyContact us Device Digital Camera Issues Product Information Warranty Index 21 U11 Y Energy StarTelevisor a Color DE Cristal Liquido LCD Modelo EnergiaMEXICANA, S.A. DE C.V Importador Sojitz MEXICANA, S.A. DE C.V