Philips 236V3L Troubleshooting, Satisfactory, you can do manual adjustments via the OSD menu

Page 34

8.Troubleshooting & FAQs

8. Troubleshooting & FAQs

8.1 Troubleshooting

This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative.

Common Problems

No Picture (Power LED not lit)

•Make sure the power cord is plugged into the power outlet and into the back of the monitor.

•First, ensure that the power button on the front of the monitor is in the OFF position, then press it to the ON position.

No Picture (Power LED is White)

•Make sure the computer is turned on.

•Make sure the signal cable is properly connected to your computer.

•Make sure the monitor cable has no bent pins on the connect side. If yes, repair or replace the cable.

•The Energy Saving feature may be activated

Screen says

Attention

Check cable connection

•Make sure the monitor cable is properly connected to your computer. (Also refer to the Quick Start Guide).

•Check to see if the monitor cable has bent pins.

•Make sure the computer is turned on.

AUTO button doesn't function

•The auto function is applicable only in VGA-Analog mode. If the result is not

satisfactory, you can do manual adjustments via the OSD menu.

Note

The Auto Function is not applicable in DVI- Digital mode as it is not necessary.

Visible signs of smoke or sparks

•Do not perform any troubleshooting steps

•Disconnect the monitor from mains power source immediately for safety

•Contact with Philips customer service representative immediately.

Imaging Problems

Image is not centered

•Adjust the image position using the “Auto” function in OSD Main Controls.

•Adjust the image position using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode.

Image vibrates on the screen

•Check that the signal cable is properly securely connected to the graphics board or PC.

Vertical flicker appears

•Adjust the image using the “Auto” function in OSD Main Controls.

•Eliminate the vertical bars using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode.

Horizontal flicker appears

•Adjust the image using the “Auto” function in OSD Main Controls.

32

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Troubleshooting & FAQs Table of Contents Safety precautions and mainte- nance OperationTemperature 0-40C 32-95F Humidity 20-80% RH Notational DescriptionsWaste Electrical and Electronic Equipment Disposal of product and packing materialWeee Package contents Setting up the monitorInstallation Install base standOperating the monitor OFFModel 236V3L for 1A model OSD MenuModel 236V3L Basic and simple instruction on the control keysRemove the Base Stand Remove Base Stand and BasePress the release button to detach the base column Setting up the monitor SmartContrast Image OptimizationPhilips SmartControl Lite Start with Standard pane Adjust menu Color menu Image Optimization At startup will not load when this box is unchecked Disabled Exit Close SmartControl Lite Task Tray Menu Disabled LED Technical SpecificationsTFT-LCD YESRohs YES Epeat Mtbf30,000hrs Environmental Packaging 100% recyclableSelective models, UL/cUL, BSMI, ISO9241-307 Compliance and standards Regulatory ApprovalsCabinet Color Black Finish Glossy/Texture Resolution & Preset Modes Power Management 236V3L Power Management DefinitionBrand owner offers take-back options Regulatory InformationLead-free Product Only for selective modelsEpeat Electronic Product Environmental GS EK1-20002009 GS mark requirementFederal Communications Commission FCC Notice U.S. Only Commission Federale de la Communication FCC DeclarationRegulatory Infomation Varoitus VarningAchtung Beim Aufstellen China RoHS Pixels and Sub pixels Customer care and warrantPhilips’ Flat Panel Monitors Pixel Defect Policy Types of Pixel DefectsTotal bright dot defects of all types Black Dot DefectsProximity of Pixel Defects Dark subpixelCustomer Care & Warranty Fujitsu IBACPS Contact Information for Apmea region AL Shahd Computer L.L.CTroubleshooting Satisfactory, you can do manual adjustments via the OSD menuGeneral FAQs Image appears distorted.Text is fuzzy or blurredQ7 How should I clean the LCD surface? Q10 Are Philips LCD monitors Plug-and- Play?Troubleshooting & FAQs Koninklijke Philips Electronics N.V. All rights reserved
Top Page Image Contents