Philips 273E3L user manual Green, red, blue, dark, and white dots appears on the screen

Page 37

8.Troubleshooting & FAQs

Horizontal flicker appears

•Adjust the image using the “Auto” function in OSD Main Controls.

•Eliminate the vertical bars using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode.

Image appears blurred, indistinct or too dark

•Adjust the contrast and brightness on On-Screen Display.

An "after-image", "burn-in" or "ghost image" remains after the power has been turned off.

•Uninterrupted display of still or static images over an extended period may cause " burn in", also known as "after-imaging " or "ghost imaging", on your screen. "Burn-in", "after- imaging", or "ghost imaging" is a well-known phenomenon in Monitor panel technology. In most cases, the "burned in" or "after-imaging" or "ghost imaging" will disappear gradually over a period of time after the power has been switched off.

•Always activate a moving screen saver program when you leave your monitor unattended.

•Always activate a periodic screen refresh application if your Monitor will display unchanging static content.

•Severe” burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired.The damage mentioned above is not covered under your warranty.

Image appears distorted.Text is fuzzy or blurred.

•Set the PC’s display resolution to the same mode as monitor’s recommended screen native resolution.

Green, red, blue, dark, and white dots appears on the screen

•The remaining dots are normal characteristic of the liquid crystal used in today’s technology, Please refer the pixel policy for more detail.

The "power on" light is too strong and is disturbing

•You can adjust “power on” light using the power LED Setup in OSD main Controls.

For further assistance, refer to the Consumer Information Centers list and contact Philips customer service representative.

35

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Troubleshooting & FAQs Table of Contents Oo Temperature 0-40C 32-95F Oo Humidity 20-80% RH Safety precautions and maintenanceOperation Notational Descriptions Weee Installation Setting up the monitorTo adjust the OSD menu Connecting to your PC Operating the monitor 273E3LChange to 43 display Off273E3L OSD MenuResolution notification 100mm Why do I need it? Smartimage Lite What is it?How does it work? Why do I need it? Philips SmartControl Lite Start with Standard pane Adjust menu Color menu Next goes to the succeeding target 6-targets Image Optimization Image Optimization Task Tray Menu Disabled Task Tray Menu EnabledExit Close SmartControl Lite TFT-LCD LCD panel typeYES Power On mode 27W typical Energy Consumption Rohs YES Epeat Mtbf720x400 273E3L Automatic PowerSavingBrand owner offers take-back options Lead-free ProductEN550241998+A12001+A22003 Epeat Electronic ProductGS EK1-20002009 GS mark requirement Reorient or relocate the receiving antenna Federal Communications Commission FCC Notice U.S. OnlyTV technician for help EN 55022 Compliance Czech Republic Only Paikka/Ilmankierto Polish Center for Testing and Certification NoticeVaroitus Plassering/VentilasjonNur original-Ersatzteile verwendet werden Ergonomie Hinweis nur DeutschlandAchtung Beim Aufstellen Pixels and Sub pixels Philips Flat Panel Monitors Pixel Defect PolicyTypes of Pixel Defects Bright Dot DefectsProximity of Pixel Defects Black Dot DefectsTypes of black dot defects Pixel Defect Tolerances01803 386 United Kingdom Invec Scotland Germany Siemens I&S0207 949 Local call tariff Ireland Invec Scotland 01 601 Local call tariff Spain Eatsa SpainBulgaria Belarus IBACroatia Estonia FujitsuEmirates Contact Information for Apmea regionCommon Problems TroubleshootingGreen, red, blue, dark, and white dots appears on the screen Power on light is too strong and is disturbingSmartControl Lite FAQs Q7 How should I clean the LCD surface? Icm? Q4 How do I adjust the resolution?Q9 Can I connect my Monitor to any PC, workstation or Mac?
Top Page Image Contents