L01_15634 (GB)
Remote control keys
&Screen information / permanent no.
To display / clear the program number, name (if it exists), time, audio mode and time remaining for the sleep feature. Press the key for 5 seconds to activate permanent display of the number.This key is also used to exit from the menu.
éSurround Sound (only available on certain versions) To activate / deactivate the surround sound effect. In stereo, this gives the impression that the speakers are further apart. For models equipped with Virtual Dolby Surround*, you can experience Dolby Surround Pro Logic sound effects. In mono, a stereo spatial effect is simulated.
“VCR key (p.11) ‘
Used to access a series of stored settings: Speech,
Music, Theatre and return to Personal.
( Menu
To call up or exit the menus.
§ Cursor
These 4 keys are used to move around the menus or provide direct access to the different 16:9
formats (p.9).
è Volume
To adjust the sound level
! Mute
To mute or restore the sound.
ç Number keys
Direct access to the programmes. For a 2 digit program, enter the 2nd digit before the dash
disappears.
à Selection of EXT socket
Press several times to select EXT1, EXT2,
ÅRadio / TV mode
To switch the TV set to radio or TV mode (for versions equipped with radio).
#Standby
Lets you place the TV set on standby.To turn on the TV, press P @ @, b, 0 to 9 (or Â).
$ Teletext keys (p. 8), VCR keys (p.11) and list of radio stations ı (p. 5)
%Sleep
To select an automatic standby after a preset time (from 0 to 240 minutes).
&16:9 modes (p. 9) ( Pre-set image
Used to access a series of stored settings: Rich,
Natural, Soft, Multimedia and return to Personal.
) Teletext (p. 8)
~ Program selection
To access the next or previous programme.The number, (name) and sound mode are displayed for a few moments.
For some programs, the title of the program will be
displayed at the bottom of the screen.
+ Teletext keys (p.8)
or VCR keys (p.11)
, Sound mode
Used to force programmes in Stereo to Mono or, for bilingual programs, to choose between Dual I or Dual II. For TV sets equipped for Nicam reception, depending on the programmes, you can force the Stereo Nicam sound to Mono or select between
Nicam Dual I, Nicam Dual II and Mono.
The Mono indication is red when in forced position.
*“Dolby” and the
Safety Information
•Plug the TV into a 220V – 240V AC, 50 Hz supply.
•Disconnect mains plug when :
–the red light below the TV screen is flashing continuously.
–a bright white line is displayed across the screen.
–there is a lightning storm.
–the set is left unattended for a prolonged period of time.
• | Cleaning the TV screen. Never use abrasive cleaning agents. Use a slight damp chamois leather or soft cloth. |
• | No naked flame sources, such as lighted candles, should be placed on top of the TV or in the vicinity. |
•Do not place your TV set under direct sunlight or heat.
•Do not cover or block the TV as it could lead to overheating.
• Leave at least 5 cm around each side of TV set to allow for proper ventilation.
•Avoid placing your set (e.g. near the window) where it is likely to be exposed to rain or water.
•Battery Usage CAUTION – To prevent battery leakage that may result in bodily injury, property damage, or damage to the unit:
–Install all batteries correctly, with + and – aligned as marked on the unit.
–Do not mix batteries (old and new or carbon and alkaline, etc.).
–Remove batteries when the unit is not used for a long time.
Useful Tips
•Do not leave your set on standby mode for a prolonged period of time. Switch off set to allow it to be demagnetised.A demagnetised set supports good picture quality.
•Do not shift or move the set around when it is switched on. Uneveness in colour in some parts of the screen may occur.
•Never attempt to repair a defective TV yourself.Always consult a skilled service personnel.
3