Philips 55PFL8007, 40PFL8007, 46PFL8007 manual Remote control, Switch on and off, Quick start

Page 20

3

TV

3.1

Switch on

Switch on and off

Make sure you plugged in the mains power on the back of the TV before you switch on the TV.

If the red indicator light is off, press the small key A on the right, on the back of the TV to put the TV on standby - the red indicator will light up.

With the TV on standby, press A on the remote control to switch the TV on. Alternatively, you can use the CH+, CH- and h key to switch the TV on.

Quick start

To switch on the TV faster than usual, you can set the TV in Quick start mode.

In Help, press *List and look up Quick start for more information.

Switch to standby

To switch the TV to standby, press A on the remote control.

Switch off

To switch the TV off, press the small key A on the right of the TV on the back. There is no red indicator light. The TV is still connected to the mains power but consumes a minimum of energy. To switch off the TV completely, disconnect the power plug.

When disconnecting the power plug, always pull the power plug, never the cord. Ensure that you have full access to the power plug, power cord and outlet socket at all times.

Quick start

With Quick start, the TV can start up faster than usual. When you switch the TV on from standby the TV picture already appears after a few seconds, if Quick start is activated.

The TV can remember your daily habit of watching TV. Some time before you usually switch on the TV, Quick start will activate automatically, allowing you to switch on quickly. Alternatively, you can select up to 3 fixed time frames a day during which the TV is ready to switch on quickly.

When you switch the TV back to standby, Quick start stays active until the set time frame ends.

Activate

To set the Quick start activation, press h and select S Setup and press OK to open the Setup menu.

Select TV settings > General settings > Quick start > Activation. You can select Automatic or Manual.

-Automatic

Select Automatic to activate Quick start automatically. The TV remembers your watching habit and activates Quick start during these time frames. With Automatic, the TV can set up to 4 time frames of 1 hour.

-Manual

Select Manual to activate Quick start during 3 fixed time frames a day. As an example, you can set a time frame in the morning, one at noon and one in the evening. For each time frame, you can set the time span yourself.

If Quick start is set to Manual, you can also select a Standby delay. With Standby delay, you can set the TV to keep Quick start active for some time after you switched the TV to standby. You can set the delay up to 1 hour in steps of 15 minutes.

Specifics

The TV clock has to work properly to activate Quick start. Quick start activation cannot be longer than a 4 hour time frame.

Quick start increases the energy consumption during standby.

3.2

Remote control

20

TV / Remote control

Image 20
Contents 01*5635 Contents Tour Smart TVApp gallery Rental videosSocial networks SkypeSmartphones and tablets Pause TV and recordingsEasyLink Setting up Tips on placementTV stand and wall mounting TV StandPower cable Wireless connectionSetting up / Network AntennaWPS pin Wired connectionStandard Network settings Setting up / Connect devicesConnect devices Tips on connectionsEasyLink Hdmi CEC ScartAudio Out Optical VGACAM Common Interface CAMCI+ Set-top box STB Satellite receiverHome Theatre System HTS Connect the dish antenna cable to the Satellite receiverBlu-ray Disc Player Audio Out levellingUSB Hard Drive DVD PlayerGame Page Install the mouse USB flash drivePhoto camera CamcorderSetup menu Quick picture settingsQuick picture settings ComputerSafety and care Temperature and humidity Screen careSwitch on Remote controlSwitch on and off Quick startKeyboard GuideAmbilight Smart TVPointer ShiftQwerty About pointerPairing Using the pointerIR Sensor BatteriesChannels CleaningWatch TV TV / Watch TV Lock a channel Channel installation Update channels Automatic updateDVB-T + DVB-C Symbol rate TV / Watch TVIf the country is correct continue with step Frequency scan Picture format TextOpen TV Guide TV guideInteractive TV Source list Switch to devicesReceiving TV guide info Subtitles and languages From standbyEasyLink SubtitlesTimers and clock Picture style Picture settingsPicture settings Location ISF CalibrationSound Sound styleAmbilight settings TV placementSwitch Ambilight on and off Ambilight settingsSwitch on Lounge lightHearing impaired Visually impairedSpeakers / Headphones Key beepWhat you need Your 3D glassesPTA507 PTA508Watch 3D Care of the 3D glasses Optimal 3D viewingHealth warning Smart TV Apps Smart TVHome menu Using Apps Videos, photos and music Rental video AppsOnline TV From a USB or networkMenu bar and sorting View photosPlay music Play videosPause TV DivX VODRecording Record a programWatch a recording To stop recording, press q Stop Schedule a recordingMyRemote App About MyRemote AppYour network Home networkApp menu App downloadApp menu App functions TV a Page What is Skype? Install the cameraSkype Start SkypeContacts No emergency callsContacts Add a contactCalling on Skype Block a contactVideo and voice call Calling phones and mobilesSkype settings Skype CreditRingtone volume Change passwordTerms of Use Sign outTwo-player games GamesPlay a game TV Specifications EnvironmentalSaving energy European energy labelPower ReceptionDisplay SoundUSB Dimensions and weightsConnectivity Software update TV SoftwareSoftware version Open source softwareUsing help and search SupportRegister Online helpDolby DivXMicrosoft Other trademarksESD IndexDVB MyRemote App, Wi-Fi smart screen Network, wiredOriginal language Sleep timer Power inletVesa WPS, PIN code WWW YPbPr connection, tips#&%&+,#-&,# ?6,*,0?%