Philips 19MD350B/F7 user manual  Supplied Accessories,  Attaching the Stand, Tilt Stand

Page 6

2 Align the 2 stand hooks with the two hooks under the bottom of the main unit (shown by arrow ➀), then slide the stand in the direction as shown by arrow ➁until it stops and the 3 mounting holes are aligned. Make sure not to put the AC power cord between the stand and the unit.

INTRODUCTION

Supplied Accessories

user manual			quick start guide	remote control	batteries	screw kit for attaching
(1EMN26003)			(1EMN26004)	(NF801UD)	(AAA, 1.5V x 2)	the stand
						(1ESA23636)
					AAA
					AAA
					AAA

•If you need to replace these accessories, please refer to the part No. with the illustrations and call our toll free customer support line found on the cover of this manual.

Attaching the Stand

You must attach the stand to the unit to have it as a table top unit. Be sure the front and rear of the stand match the proper direction.

1 Spread a thick and soft cloth over a	3 Drive Phillips pan screws in the 3
table as shown below.	threaded holes at the bottom of the
Place the main unit face down onto it.	stand until they are tight.
Make sure not to damage the screen.

front	side

To remove the stand from this unit

Unscrew the Phillips pan screws indicated by above

“➂” screw holes. After the screws are removed pull the stand up toward the rear of the unit. Be careful not to drop the stand when you remove it.

screw holes

Note:

•When attaching the stand, ensure that all screws are tightly fastened. If the stand is not properly attached, it could cause the unit to fall, resulting in injuries as well as damage to the unit.

•Make sure to use a table which can support the weight of this unit and is larger than this unit.

•Make sure the table is in a stable location.

Tilt Stand

-2.5°

10°

You can adjust the stand to change the angle of the unit (-2.5° to 10°).

6

EN

Image 6

Contents 19MD350B Notification For Customer UseImportant Safety Instructions Read before operating equipmentIntroduction  PrecautionLaser Safety Important Copyright InformationTo Avoid the Hazards of Electrical Shock and Fire  Symbols Used in this Manual Trademark Information Location and HandlingTilt Stand  Supplied Accessories Attaching the Stand To remove the stand from this unit Features DTV/TV/CATV Contents TV FunctionsDVD Functions  Control Panel  TerminalsAnalog mode TV  Remote Control FunctionDigital mode DTV DVD mode Installing the Batteries Battery Precautions Connection to Cable Receiver or Satellite Box Preparation Antenna Connection Satellite provider External Device Connection Hdmi ConnectionHDMI-DVI Connection Component video Connection Video ConnectionAudio Output Connection for digital broadcasting only  Plug In the AC Power Cord ResolutionPC Connection Before you begin TV Functions  Initial SetupAfter an initial setup is completed Make sure the unit is connected to antenna or cableWatching TV  Volume Adjustment Sleep Timer  Channel Selection Still Mode  Switching Each Input ModeSwitching Audio Mode Press Info  TV Screen InformationBroadcasting information Selected program TV Screen Display Mode For 169 video signalFor PC input signal Optional Setting  Main Menu Autoprogram Press Menu to exit  Channel ListUse Cursor K/L to select Channel List, then press Channel you want to add, then press OK Antenna Confirmation  Language SelectionUse Cursor K/L to select Antenna, then press OK Use Cursor K/L to select the desired setting, then press OK  Picture AdjustmentAdjust the picture quality Smart PictureSmart Sound  Sound AdjustmentTV Speakers EqualizerCaption Service Caption mode Closed Caption Digital Caption Service To select Digital Caption ServiceUse Cursor K/L to select On, then press OK Font Color Font StyleFont Size Font OpacityChannel Lock  Child LockUse Cursor K/L to select Child Lock, then press Change PINAssociation of America Channel LockUS Movie ratings lock Press Menu to exitUS TV ratings lock To set the sub ratingsUse Cursor K/L to select US TV ratings lock, then press OK Change PIN Use Cursor K/L to select Change PIN, then pressClock, Phase  PC SettingsAuto Adjustment Horizontal Position, Vertical PositionUse Cursor K/L to select Energy Saving Mode, then press OK  Energy Saving ModeLocation Use Cursor K/L to select the desired mode, then press OK Current Software Info Confirm the version of the software currently usedOperating DVD DVD Functions Playable Media Unplayable Media  Resume Playback  Playback Disc Menu DVD Fast Forward / Fast Reverse  Slow Forward / Slow Reverse Zoom Chapter / Title / Track Search During playback, press Mode repeatedly until / appears Search Functions You can select chapters, titles or tracks on the discTime Search Direct Search Repeat Playback Repeat A-B Playback Programmed Playback  Random PlaybackYou can repeat playback between a and B on a disc  Special Settings  On-screen DisplaySubtitle Language Camera Angles Black Level SettingPress Cursor K/ L to adjust the black level Audio LanguageAppears Stereo Sound ModeVirtual Surround Press Cursor K/ L to select the sound levelSubtitle *1, *2Default OFF DVD Setting DVD Language Setting Audio *1, *2 DVD Audio Setting Down SamplingNumber buttons to enter the current 4-digit password  Parental SettingIf you have set password already, use Use the Number buttons to enter the new 4-digit password Others You can change the other functions Reset to the Default Setting  Language Code List LanguageTroubleshooting There is no clock function on this unitTroubleshooting  Troubleshooting GuideTape containing captions Have been read during copying During playback Angle does not switchCaptions are displayed as a Make sure the disc is compatible with the unit Glossary  MaintenanceInformation AtscCatv LCDLimited Warranty Ninety 90 DAY Labor / ONE 1 Year Parts Français