Philips BDS4221/00 user manual Regulatory Notice, FCC Statement, IC Compliance Notice

Page 4

Regulatory Notice

FCC Statement

The Federal Communications Commission Radio Frequency Interference Statement includes the following warning:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television receptions, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Warning

User must use shielded signal interface cables to maintain FCC compliance for the product. Provided with this display is a detachable power supply cord with IEC320 style terminations. It may be suitable for connection to any UL Listed personal computer with similar configuration. Before making the connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor and that the ampere rating

of the computer convenience outlet is equal to or exceeds the monitor voltage rating. For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P type (parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable power supply cord with NEMA configuration 6015P type (tandem blades) plug cap.

IC Compliance Notice

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regula- tions of ICES-003.

Cet appareil Numerique de classe B respecte toutes les exigences du Reglemont NMB-03 sur les equipements produisant des interferences au Canada.

Notice de Conformit IC

Cet appareil numerique de classe B respecte toutes les exigences du Reglement ICES-003 sur les equipements produisant des interferences au Canada.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Philips Business Solutions Important Safety Instructions Special NoticesSpecial Warranty Information Cleaning & MaintenanceCell Defects FCC Statement Regulatory NoticeIC Compliance Notice Table of Contents Page Getting to Know Your Display Flat Panel MonitorPackage Contents Getting to Know Your DisplayFront Panel Controls Rear Panel Rear Panel ConnectionsRemote Control Getting to Know Your Display Display Connections Connecting a VCR Connecting TV or CatvDisplay Connections Connecting a DVD Player Using component video inputConnecting to an External Amplifiers Connecting a DVD con’tExternal Audio Connections Connecting a PC Connecting external amplified speakersUsing RGB or DVI Video Input Setting Up Your Monitor Using Plug and Play Connecting a PC con’tHow to Set up Your PC for Use with Monitor Windows Supported Resolutions Display Connections Basic Operations Powering On/Off Using Front Panel or Remote ControlBasic Operations Changing InputsVolume Adjustment Using MuteAccessing OSD Menu via Remote Control or Front Panel On-Screen Display MenuOn-Screen Status Display Displaying StatusFor 43 Square Content For Widescreen ContentUnderstanding Widescreen Modes NormalChanging Aspect Ratios Using Remote ControlZoom Key Picture Controls Adjusting Picture Settings Using. OSD MenuExplanation of Various Picture Control Settings Picture ControlsBrightness Picture-in-Picture / Side-by-Side Picture Turning On PIP/Side-by-Side Picture POPSelecting Signal Source for Sub-Picture Selecting Signal Source for Main PictureSource Select Input selectChanging Channels in PIP Mode Picture-in-Picture / Side-by-Side Picture Con’tMain and Sub-Window Swap Changing Location of PIP ImageSelecting Color Temperature Fine Tuning RGB ModePicture Controls Sound Controls Adjusting Sound Settings Sound ControlsExplanation of Various Sound Control Settings TrebleSetting Output Using OSD Menu Built-in Amplification SpeakerTurning. On Built. -in Amplification Fixed / Variable Audio OutputAdvanced Functions Advanced Functions Setting. OSD Menu LanguageOSD Menu Language Power Save Mode Settingj Power Save Mode Using OSD MenuInformation Display Accessing Information Display MenuExplanation of Information Version Using the Teletext NewsflashSubtitles AlarmFasttext TV Functions Initial Set Up TV FunctionsTV Functions Channel Manual SearchChannel Edit On-Screen Status Display TV Mode Using Remote Control or Front PanelTV Mode Single Tuner Changing ChannelsAccessing via OSD Menu Accessing via Remote ControlAppendix Flat Panel DisplayTroubleshooting AppendixWall Mount Instructions Appendix Specifications Specifications Con’t TTL VGAPin Assignments For D-SUB connector in / loop out Pin Assignments For 24 Pin DVI connector digital onlyMaximum Resolution PB/PR For Component 1Power Management Mode Sync Video Power dissipation AcousticsSound Reliability RequirementPreset Timing Chart Mode NoAppendix
Top Page Image Contents