Philips BDL5231V user manual Setup Procedure

Page 18

User Manual BDL5231V/00

Setup Procedure

1. Install the system on the right location

CAUTION:

THE LCD MONITOR MUST BE MOVED OR INSTALLED BY TWO OR MORE PERSONS.

Failure to follow this caution may result in injury and damage when the LCD monitor falls.

CAUTION:

DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY YOURSELF.

The LCD display must be installed by a qualified technician. Contact your dealer for more information.

CAUTION:

DO NOT MOUNT OR OPERATE THE DISPLAY UPSIDE DOWN, FACE UP OR FACE DOWN.IT’S POSSIBILITY TO CLOCKWISE 90 DEGREES MOUNT. BUT DO NOT COUNTERCLOCKWISE 90 DEGREES MOUNT.

CAUTION:

DO NOT INSTALL THE LCD MONITOR WHERE IT WILL BE EXPOSED TO DIRECT SUNLIGHT.

Failure to follow this caution will result in display defects.

IMPORTANT:

Lay the protective sheet, which was wrapped around the LCD monitor when it was packaged, beneath the LCD monitor so as not to scratch the panel.

2. Install the remote control batteries

The remote control is powered by 1.5V AAA batteries. To install or replace batteries:

1.Press and slide to open the cover.

2.Align the batteries according to the (+) and (–) indications inside the case.

3.Replace the cover.

CAUTION:

Incorrect use of batteries can result in leaks or bursting. Be careful especially about the following points.

Place “AAA” batteries matching the + and - signs on each battery to the + and - signs of the battery compartment.

Do not mix battery types.

Do not combine new batteries with used ones. It causes shorter battery life or leakage of batteries.

Remove dead batteries immediately to prevent battery

liquid from leaking into the battery compartment. Don't touch exposed battery acid, it cause damage to your skin.

NOTE:

If you do not intend to use the Remote Control for a long period, remove the batteries.

3. Connect to external equipment

To protect the connected equipment, turn off the main power before making connections.

Please refer to section “Connectivity” P.18~P.22 for operations..

4. Connect power cord

The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.

Fully insert the prongs into the power outlet socket. Loose connection may cause noise.

NOTE:

Please refer to “Safety Operation” section of this manual for proper selection of AC power cord.

5. Turn on the power of the attached external equipment

When connected with a computer, turn on the power of the computer first.

6. Operate the attached external equipment

Display the signal from the external equipment.

7. Adjust the sound

Make adjustments to lower or to rise the volume as required.

8. Adjust the screen

Make adjustments to the display position or settings if required.

15

Image 18
Contents Public Signage Solutions Table of Contents Page Safety Instructions Regulatory Information CE Declaration of Conformity Polish Center for Testing and Certification Notice Information for UK only 环保使用期限 North Europe Nordic Countries Information Contents Connection & Button Overviews Control PanelTerminal Panel External Speaker TerminalRemote Control Power buttonOperating Range for the Remote Control Handling the remote controlHow to Mount or Attach Feet to the LCD Monitor Way 1 Attach and remove the optional standsWay II Mount the monitor on the wall To avoid monitor from fallingVentilation Requirements for enclosure locating Setup Procedure Adjust the image Recommended AdjustmentTo prevent the main power switch from being changed Install the LCD Monitor in Portrait Mode How to set-upConnectivity Diagram ConnectivityBefore making connections Connecting to a Personal Computer Connecting the LCD Monitor to a Personal ComputerConnecting to a Digital Interface Equipment Connect the LCD Monitor to a Computer with a Digital OutputConnecting to a DVD Player Connect the LCD Monitor to a DVD PlayerConnecting to a Stereo Amplifier Connecting to a mount PCConnect the LCD Monitor to a Stereo Amplifier Pressing the power button Power on and OFF ModesPressing the Main Power Switch Using the remote controlDisplay Signal of Video Source Setting to Video Power IndicatorUsing Power Management Picture SizeControl Lock Mode Smart Picture ModeAudio Source Switching OSD InformationOSD On-Screen-Display Controls Sharpness BrightnessContrast Black LevelColor Control Color TemperaturePicture Reset Light SensorZoom Mode PositionScreen Reset Custom ZoomTreble Speaker Audio ResetBalance BassPIP Reset PIP SizePIP Audio Power Save LanguagePanel Saving Configuration Reset Factory ResetInformation OSD Sleep TimerOSD Turn OFF OSD H PositionMonitor Information Advanced Option Gamma SelectionTiling IR ControlKeyboard Control Date and TimeSchedule Smart PowerAdvanced Option Reset Monitor IDFor long life use of Public Display Image Sticking of LCD PanelRecommendations Remote control numbering function B a B aFeatures Full HD LCD display 1920x1080pTroubleshooting No Signal is displayed on the screen Remote Control is not availableSCHEDULE/SLEEP Timer function is not working properly No SoundSpecifications Specifications BDL5231VPin Assignment SDASpecifications are subject to change without notice