Philips BDL6531E user manual Information for UK only, How to connect a plug

Page 6

User Manual BDL6531E

INFORMATION FOR UK ONLY

WARNING - THIS APPLIANCE MUST BE EARTHED. Important:

This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows:

1. Remove fuse cover and fuse.

2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type.

3. Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place.

If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A.

Note: Any severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured in accordance with the following code:

BLUE - “NEUTRAL” (“N”)

BROWN - “LIVE” (“L”)

GREEN & YELLOW - “EARTH” (‘E”)

1.The GREEN AND YELLOW wire must be connected to the terminal in the plug

which is marked with the letter “E” or by the Earth symbol or coloured GREEN or GREEN AND YELLOW.

2.The BLUE wire must be connected to the terminal which is marked with the letter “N” or coloured BLACK.

3.The BROWN wire must be connected to the terminal which marked with the letter “L” or coloured RED.

Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the three wires.

Image 6
Contents BDL6531E Maintenance Safety and Troubleshooting InformationSafety precautions and maintenance OperationService Federal Communications Commission FCC Notice U.S. Only Regulatory InformationCE Declaration of Conformity FCC Declaration of ConformityPolish Center for Testing and Certification Notice ELECTRIC, Magnetic and Electronmagnetic Fields EMFHow to connect a plug Information for UK only中国电子信息产品污染控制表示要求 中国 RoHS 法规标示要求 产品中有毒有害物质或元素 的名称及含量 Varoitus North Europe Nordic Countries InformationVarning END-OF-LIFE DisposalTable of Contents Page Unpacking and Installation UnpackingHow to remove the logo Parts and Functions Smart Insert installation holes Power buttonPower indicator ENTER/VIDEO Source buttonSpeakers R/L Audio in AUDIO1Audio OUT R/L Video in HdmiRemote Control General Functions UP button Auto Adjust buttonDisplay button Down buttonInserting the Batteries in the Remote Control Using the Cable Retainer Using the Switch Cover Connections to External EquipmentUsing S-VIDEO Input Connecting a PC Using VGA Input Using DVI Input External Audio Connection Connecting External Speakers Connecting Another BDL6531E Display OSD Menu Navigating the OSD Menu Using the DISPLAY’S Control Buttons Brightness Color TemperatureOSD Menu Overview Picture Menu ContrastLight Sensor Video Picture ResetColor Control Smart ContrastPosition Clock PhaseZoom Mode ClockScreen Reset Custom ZoomMute VolumeLINE-OUT Audio Reset Audio SourcePIP Reset PIP SizeLarge Middle Small PIP Audio Power Save Configuration 1 MenuAuto Adjust LanguageConfiguration Reset Factory ResetOSD Turn OFF OSD ModeSleep Timer PortraitBlack Level Expansion Input ResolutionNative Scan Mode Middle High Gamma SelectionIR Control Film ModeProgressive Keyboard ControlTiling Monitors = PositionHeat Status Date and TimeSchedule Monitor ID DDC/CIAdvanced Option Reset Smart PowerHigh Auto Signal Detection OFFSdtv Resolution Input ModeVGA Resolution Hdtv ResolutionReturn to the Contents Dot definition = What is a defective Dot? Pixel Defect PolicyBright DOT Defects Total DOT Defects of ALL TypesFront Panel Cleaning Instructions Cleaning and TroubleshootingCleaning Cabinet Cleaning InstructionsTroubleshooting Use the Zoom Mode or CustomIn/Out Terminals Technical SpecificationsDisplay GeneralEnvironmental Condition Internal Speaker
Related manuals
Manual 50 pages 11.06 Mb