Philips BDL6531E Safety and Troubleshooting Information, Safety precautions and maintenance

Page 2

User Manual BDL6531E

SAFETY AND TROUBLESHOOTING INFORMATION

Safety precautions and maintenance

WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards.

Read and follow these instructions when connecting and using your display:

Operation:

Keep the display out of direct sunlight and away from stoves or any other heat sources.

Remove any object that could fall into the ventilation holes or prevent proper cooling of the display’s electronics.

Do not block the ventilation holes on the cabinet.

When positioning the display, make sure the power plug and outlet are easily accessible.

When turning off the display by detaching the power cord, wait for 6 seconds before re-attaching the power cord for normal operation.

Ensure the use of an approved power cord provided by Philips at all times. If your power cord is missing, please contact your local service center.

Do not subject the display to severe vibration or high impact conditions during operation.

Do not knock or drop the display during operation or transportation.

Maintenance:

To protect your display from possible damage, do not put excessive pressure on the LCD panel. When moving your display, grasp the frame to lift; do not lift the display by placing your hand or fingers on the LCD panel.

Unplug the display if you are not going to use your display for an extensive period of time.

Unplug the display if you need to clean it with a slightly damp cloth. The screen may be wiped with a dry cloth when the power is off. However, never use organic solvent, such as alcohol, or ammonia-based liquids to clean your display.

To avoid the risk of shock or permanent damage to the set, do not expose the display to dust, rain, water or an excessively moist environment.

If your display becomes wet, wipe it with a dry cloth as soon as possible.

If a foreign substance or water gets in your display, turn the power off immediately and disconnect the power cord. Then remove the foreign substance or water, and send the display to the maintenance center.

Do not store or use the display in locations exposed to heat, direct sunlight or extreme cold.

In order to maintain the best performance of your display and ensure a longer lifetime, please use the display in a location that falls within the following temperature and humidity ranges.

-Temperature: 0 ~ 40 C 32-104 F

-Humidity: 20-80% RH

IMPORTANT: Always activate a moving screen saver program when you leave your display unattended. Always activate a periodic screen refresh application if your display will show unchanging static content. Uninterrupted display of still or static images over an extended period may cause “burn in”, also known as “after-imaging” or “ghost imaging”, on your screen. This is a well-known phenomenon in LCD panel technology. In most cases, the “burned in” or “after-imaging” or “ghost imaging” will disappear gradually over a period of time after the power has been switched off.

WARNING: Severe "burn-in" or "after-image" or "ghost image" symptoms will not disappear and cannot be repaired. This is also not covered under the terms of your warranty.

Image 2
Contents BDL6531E Maintenance Safety and Troubleshooting InformationSafety precautions and maintenance OperationService Federal Communications Commission FCC Notice U.S. Only Regulatory InformationCE Declaration of Conformity FCC Declaration of ConformityPolish Center for Testing and Certification Notice ELECTRIC, Magnetic and Electronmagnetic Fields EMFHow to connect a plug Information for UK only中国电子信息产品污染控制表示要求 中国 RoHS 法规标示要求 产品中有毒有害物质或元素 的名称及含量 Varoitus North Europe Nordic Countries InformationVarning END-OF-LIFE DisposalTable of Contents Page Unpacking and Installation UnpackingHow to remove the logo Parts and Functions Smart Insert installation holes Power buttonPower indicator ENTER/VIDEO Source buttonSpeakers R/L Audio in AUDIO1Audio OUT R/L Video in HdmiRemote Control General Functions UP button Auto Adjust buttonDisplay button Down buttonInserting the Batteries in the Remote Control Using the Cable Retainer Using the Switch Cover Connections to External EquipmentUsing S-VIDEO Input Connecting a PC Using VGA Input Using DVI Input External Audio Connection Connecting External Speakers Connecting Another BDL6531E Display OSD Menu Navigating the OSD Menu Using the DISPLAY’S Control Buttons Brightness Color TemperatureOSD Menu Overview Picture Menu ContrastLight Sensor Video Picture ResetColor Control Smart ContrastPosition Clock PhaseZoom Mode ClockScreen Reset Custom ZoomMute VolumeLINE-OUT Audio Reset Audio SourceLarge Middle Small PIP Audio PIP ResetPIP Size Power Save Configuration 1 MenuAuto Adjust LanguageConfiguration Reset Factory ResetOSD Turn OFF OSD ModeSleep Timer PortraitBlack Level Expansion Input ResolutionNative Scan Mode Middle High Gamma SelectionIR Control Film ModeProgressive Keyboard ControlTiling Monitors = PositionSchedule Heat StatusDate and Time Monitor ID DDC/CIAdvanced Option Reset Smart PowerHigh Auto Signal Detection OFFSdtv Resolution Input ModeVGA Resolution Hdtv ResolutionReturn to the Contents Dot definition = What is a defective Dot? Pixel Defect PolicyBright DOT Defects Total DOT Defects of ALL TypesFront Panel Cleaning Instructions Cleaning and TroubleshootingCleaning Cabinet Cleaning InstructionsTroubleshooting Use the Zoom Mode or CustomIn/Out Terminals Technical SpecificationsDisplay GeneralEnvironmental Condition Internal Speaker
Related manuals
Manual 50 pages 56.5 Kb