Philips BDL6520 user manual Audio menu, PIP menu, Position

Page 24

BDL6520EL

H position

Moves the horizontal position of the image left or right.

V position

Moves the vertical position of the image up or down.

Screen reset

Reset all settings in the Screen menu to factory preset values.

4.2.3. Audio menu

Audio reset

Reset all settings in the Audio menu to factory preset values.

Card OPS audio

Select the analog or digital audio mode for card OPS.

4.2.4. PIP menu

Picture

PIP

 

 

PIP input

Screen

PIP change

 

Audio

PIP size

 

 

PIP audio

PIP

PIP reset

 

Picture

Screen

Audio

PIP

Configuration1

Configuration2

Advanced option

Balance

Treble

Bass Volume Maximum volume Minimum volume Mute

Audio source Audio reset Card OPS audio

Configuration1

Configuration2

Advanced option

PIP

Select the PIP (Picture-in-Picture) mode.

Choose from: {Off} / {PIP} / {POP} / {PBP aspect} / {PBP full}.

PIP input

Select the input signal for the sub-picture.

Balance

Adjust to emphasize left or right audio output balance.

Treble

Adjust to increase or decrease higher-pitched sounds.

Bass

Adjust to increase or decrease lower-pitched sounds.

Volume

Adjust to increase or decrease the audio output level.

Maximum volume

Adjust your own limitation for the maximum volume setting.This stops the volume from being playing at too loud a level.

Minimum volume

Adjust your own limitation for the minimum volume setting.

Mute

Turn the mute function on/off.

Audio source

Select the audio input source according to the audio signal source connected to the audio input and HDMI sockets on the display.

PIP change

Enlarges the smaller picture to become the main picture, and vice versa.

PIP size

Select the size of the sub picture in the PIP (Picture-in-Picture) mode. Choose from: {Small} / {Medium} / {Large}.

PIP audio

Select the audio source in the PIP (Picture-in-Picture) mode.

{Main} – Select audio from the main picture

{Sub} – Select audio from the sub picture.

PIP reset

Reset all settings in the PIP menu to factory preset values.

NOTES:

The PIP function is available only under the following condition:

Set OSD option {Configuration1} {Panel saving} {Pixel shift} setting to {Off}, and set OSD option {Advanced option} {Tiling} {Enable} setting to {No}.

The PIP function is available only for certain signal source combinations as shown in the table below.

The availability of the PIP function will also depend on the resolution of the input signal being used.

  







 

Main Picture

HDMI

DVI-D

VGA

YPbPr

S-Video

Video

Card

Sub Picture

OPS

 

 

 

 

 

 

HDMI

X

X

X

X

O

O

X

DVI-D

X

X

X

X

O

O

X

VGA

X

X

X

X

O

O

X

YPbPr

X

X

X

X

O

O

X

Video

O

O

O

O

X

X

O

Video

O

O

O

O

X

X

O

Card OPS

X

X

X

X

O

O

X

(O: PIP function available, X: PIP function unavailable)

16

Image 24
Contents BDL6520EL Safety Instructions Know These Safety SymbolsRegulatory Information CE Declaration of ConformityFederal Communications Commission FCC Notice U.S. Only Polish Center for Testing and Certification Notice Electric, Magnetic and Electronmagnetic Fields EMFHow to connect a plug Not simply over the three wiresInformation for U.K. only 中国电子信息产品污染控制标识要求 中国RoHS法规标示要求 产品中有毒有害物质或元素 的名称及含量 China RoHSNorth Europe Nordic Countries Information End-of-Life DisposalWaste Electrical and Electronie Equipment-WEEE For customers in Canada and U.S.ATable Of Contents Unpacking and Installation Package ContentsInstallation Notes UnpackingMounting on a Wall Ventilation Requirements for enclosure locatingHow to use the logo guider for portrait position How to remove the logoMounting in Portrait Position Fold down both of its edgesParts and Functions Control PanelInput/Output Terminals RS232C in / RS232C OUTRJ-45 VGA OUT D-SubRemote Control General functionsInserting the batteries in the remote control Handling the remote controlOperating range of the remote control Freeze operationConnecting External Equipment Using the Switch CoverConnecting External Equipment DVD/VCR/VCD Using Component video inputUsing Hdmi video input Connecting a PC Using VGA inputUsing DVI input Using Hdmi inputConnecting Audio Equipment Connecting external speakersConnecting an external audio device External Speakers Speaker SwitchConnecting Multiple Displays in a Daisy-chain Configuration Control connectionVideo connection RS-232C RS232C RS232C OUTFixing your external PC OSD Menu OSD Menu OverviewNavigating the OSD Menu Screen menu Audio menu PIP menuPosition Configuration1 menu Configuration2 menu Advanced option menuFrame comp. Yes Frame comp. No Heat statusDate and time ScheduleAdvanced option reset Smart powerAuto signal detection APM Advanced Power ManagementInput Mode PC ResolutionSdtv Resolution Hdtv ResolutionDot definition = What is a defective Dot? Pixel Defect PolicyPixels and Sub-Pixels Types of Pixel Defects + Dot DefinitionDark Dot Defects Proximity of Pixel DefectsPixel Defect Tolerances MuraCleaning and Troubleshooting CleaningFront Panel Cleaning Instructions Cabinet Cleaning InstructionsTroubleshooting Technical Specifications DisplayIn/Out Terminals GeneralEnvironmental Condition Internal Speaker