Behringer UB2222FX-PRO Mute Solo, Stereo AUX Return 1/2 to AUX Send Main MIX / to Subs, To Subs

			￿
Press the MUTE switch to mute the monitor send.		￿￿	￿￿￿￿￿	￿￿		￿￿￿￿￿￿￿￿￿￿￿	￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿
EURORACK UB1622FX-PRO/UB1832FX						!"#$
		-PRO/UB2222FX-PRO/UB2442FX-PRO
MUTE		￿￿￿￿￿￿￿￿￿
SOLO
The SOLO switch routes the monitor send to the solo bus
				￿￿￿'
(post-fader and post-mute) or to the PFL bus (pre-fader and
pre-mute). The position of the MODE switch in the main section					STEREO AUX		STEREO AUX
						!"#$	RETURN￿(TO AUX
determines which of the buses is selected.		AUX SEND ￿		￿￿￿()￿￿RETURN ￿￿
					connectors		SEND ) control
2.3.5 Stereo aux return control
STEREO AUX RETURN 1					STEREO AUX		MONITOR switch of
		AUX SEND ￿			￿%￿￿￿￿￿￿&
The STEREO AUX RETURN 1 control determines the level of							the FX/AUX￿￿RET
					RETURN ￿￿
this signal in the main mix. If STEREO AUX RETURN 1 is used as					connectors
						!"#$
effects return, this will determine the level of the effects when
mixed with any “dry” channel signal.					STEREO AUX		STEREO AUX
+ When used in this way, the effects device should		AUX SEND￿￿		RETURN￿￿￿￿￿￿￿connectors￿￿			RETURN ￿￿(TO AUX
be set at 100% effect.							SEND ￿) control
					STEREO AUX		STEREO AUX
		AUX SEND ￿			RETURN ￿￿		RETURN ￿(TO AUX
					connectors		SEND ￿) control
					STEREO AUX		STEREO AUX
		AUX SEND￿￿			RETURN ￿￿		RETURN ￿(TO AUX
					connectors		SEND ￿) control
		Tab. 2.1: Connectors and controls for monitor mix with effect
	STEREO AUX RETURN FX
		On consoles UB1622FX-PRO and UB1832FX-PRO this is the
	STEREO AUX RETURN 2, on consoles UB2222FX-PRO and
	UB2442FX-PRO this is the STEREO AUX RETURN 3.
		Use the STEREO AUX RETURN FX control to determine the
	level of the signal routed from the AUX RETURN FX jacks to the
Fig. 2.12: Stereo aux return and	main mix. If nothing is connected to these jacks, the output of the
stereo aux return (to aux send) controls	built-in effects module will appear.
STEREO AUX RETURN 1/2 (TO AUX SEND)	MAIN MIX / TO SUBS
		This switch routes the signal fed in via the STEREO AUX
The two right-hand STEREO AUX RETURN controls have a
	RETURN FX jacks either to the main mix (not pressed) or to the
special function: they can be used to add an effect to a monitor
	submix (pressed).
mix. An example follows (UB1622FX-PRO wired to an effects
device):		On the UB2442FX-PRO you can select which subgroup the
Monitor mix with effect	signal is assigned to (switches 1-2 / 3-4, to the right of MAIN MIX /
	TO SUBS).
In this instance, your effects device should be set up as follows:
the AUX SEND 2 jack should be connected to the L/Mono input of	SOLO RETURNS
your effects device, with its outputs coming back into the STEREO		Additionally, this model allows you to route the aux returns
AUX RETURN 1 jacks.	together to the solo bus and the PFL bus. The LED lights up when
Connect the AUX SEND 1 jack output to the amplifier of your	Solo is on.
monitor system. The AUX SEND 1 master control determines the	STEREO AUX RETURN 4 (UB2442FX-PRO only)
overall volume of the monitor mix.		This control behaves the same way as the other stereo aux
Using the STEREO AUX RETURN (TO AUX SEND) control, the	returns. Additionally, it provides for a simple monitor path using
	the switch CTRL ROOM & PHONES ONLY.
effect signal can now be blended into the monitor mix.
You can easily use the headphones distribution amplifier	CTRL ROOM & PHONES ONLY
		Use this switch to route the signal appearing at the AUX
BEHRINGER POWERPLAY PRO HA4600/HA4700/HA8000 to
	RETURN 4 jacks to the control room and headphones outputs.
provide four (HA8000: eight) stereo headphone mixes for your
studio.			2.3.6 Supplement to UB1832FX-PRO
The following table shows which jacks on the console can be
		The UB1832FX-PRO has a stereo fader for the AUX RETURN
used for this purpose.
	FX and offers a variety of routing options: MUTE disables the
	effect return (but not PFL of course!), SOLO routes it to the Solo
	or PFL busses, SUB to the subgroups and MAIN to the main mix.

2. CONTROL ELEMENTS AND CONNECTORS 9