Setting Up your DVD/VCR
Connecting to Optional Equipment (for DVD features)
•A digital component with a
•The player outputs the surround sound signals from the DIG- ITAL OUT COAXIAL or OPTICAL connector.
If your receiver has a MPEG 2 or Dolby Digital™ decoder,
1Connect the COAXIAL or OPTICAL DIGITAL AUDIO OUT of the DVD/ VCR to the COAXIAL or OPTICAL DIGITAL AUDIO IN on your receiver.
Notes:
–If the audio format of the digital output does not match the capabilities of your receiver, the receiver will pro- duce a strong, distorted sound or no sound at all.
–MP3 Audio is not available on the Digital Output.
–You will still need the video cable or RF coaxial cable for VCR features.
AUDIO RECEIVER
|
| OPTICAL DIGITAL |
| |
|
| AUDIO IN |
| |
|
| COAXIAL DIGITAL |
| |
|
| AUDIO IN |
| |
| DVD |
|
|
|
DIGITAL | ANALOG |
| AERIAL | |
AUDIO OUT | AUDIOOUT | OUT |
|
|
| L | VCR | AV2(DECODER) |
|
|
|
|
| |
OPTICAL COAXIAL | DVD/VCR | AV1(TV) | RF OUT | |
R
External Input Mode (for VCR features)
To receive the signal from an external input (decoder, satellite receiver, video camera, another VCR etc.), connect to the AV2 (DECODER) socket, and enter “002” with numerical key pads to appear “AV2” on the TV screen.
If you use the AV1 (TV) socket, enter “001” with numerical key pads to appear “AV1” on the TV screen.
If you use the front AUDIO/VIDEO input jacks, enter “003” with numerical key pads to appear “AV3” on the TV screen.
Playable Video Cassette Tapes
Philips Consume Electronics recommends that only video cas- sette tapes that have the VHS mark and High Quality (HQ) sys- tem is compatible with this DVD/ VCR.This
DVD/ VCR has an Automatic Head Cleaner.
| Recording Prevention | 1 |
| Video cassette tapes have record tabs to | |
1 | ensure recordings are not erased accidentally. | |
To prevent recording, break off the tab with a |
| |
2 | 2 | |
To allow recording, cover the hole with cello- | ||
| phane tape. |
Notes:
–Use only tapes with VHS mark.
–Remove any adhesive
–Periodic maintenance is required to maintain your DVD/ VCR performance.
–Video heads will require replacement after a period of time. Only an authorised service center should perform this service.
Turning on your DVD/VCR
The following steps only be performed when you insert the AC PLUG at the first time.
1 Turn on the TV and select the video channel on the TV.
2 Plug in the DVD/VCR.
3 Confirm with P+.
The automatic TV channel search starts.
4 | “TIME” and “DATE” will appear on |
|
|
5 | the TV screen. |
|
|
Check “TIME”. If required, please |
|
| |
| change the time with numerical key |
| PLEASE WAIT |
6 | pads. |
|
|
Check if the displayed settings for | START | FINISH | |
| “DAY”,“MONTH” and “YEAR” are | ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ | |
7 | correct. |
|
|
When all information is correct, |
|
| |
| save by pressing STATUS/EXIT.The |
|
|
preparation for use is now com-
Inserting batteries into the Remote Control
1Open the battery cover.
2 Insert batteries (AA size) with the correct polarity as indicated by the + and - symbols inside the battery
plete.
TIME
DATE
SMART CLOCK [ON]
compartment.
3Close the cover.
CAUTION!
–Remove batteries if they are exhausted or not to be used for a long time.
–Do not use old and new or different types of batteries in combination.
–Batteries contain chemical substances, so they should be disposed off properly and kept away from children.
Using the Remote Control
•Direct the remote control at the remote sensor of the DVD/ VCR.
•Do not drop the remote control.
•Do not leave the remote control near extremely hot or humid place.
•Do not spill water or put anything wet on the remote con- trol.
Note:END=EXIT
–If the DVD/VCR has been completed AUTO TUNING at this procedure, this initial menu has never shown even if power failure is occured or inserted AC plug again.)
7