Philips CCZ191AT Hooking Up The TV/VCR, Hook up your TV/VCR using one of the connections shown

Page 6

CCZ191/CCZ191comb.QX33 4/6/99 6:42 PM Page 6

6 Hooking Up The TV/VCR

1

Hook up your TV/VCR using one of the connections shown.

A.

Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna

Connect a Cable signal or an antenna to the ANT(enna) Jack.

ANT.

B.

Hooking Up Your TV/VCR With a Cable Box

To view any channel, set the TV/VCR to the Cable Box output channel (channel 03 or 04). Then, select channels at the Cable Box.

Connect the Cable signal to the IN Jack on the Cable Box.

Connect an RF coaxial cable (75-
ohm, not supplied) to the OUT Jack
on the Cable Box and to the	OUT	IN
ANT(enna) Jack on the TV/VCR.

ANT.

ANT.

C.

Hooking Up Your TV/VCR With an Indoor Antenna

To install a rod antenna (not sup- plied), push the stem of the antenna into the antenna hole on the top of the TV/VCR. Connect the antenna wire to the ANT(enna) Jack on the back of the TV/VCR as shown. Extend the antenna and adjust its length, direction, and angle for the clearest picture.

Rod Antenna

(not supplied)

ANT.

Image 6

Contents CCZ191AT CCZ192AT Dear Philips Magnavox product owner For Customer UseFeatures Safety PrecautionsIntroduction Table of Contents Using the Remote Control Before Using the TV/VCRPutting Batteries in the Remote Control VCR MaintenanceANTenna Jack on the TV/VCR Hook up your TV/VCR using one of the connections shownHooking Up The TV/VCR Rod AntennaBent pin Hooking Up The TV/VCR cont’dAudio and video cables are not supplied Crooked Pin Straight PinYou cannot set up channels if you are using a Cable Box Turning On the TV/VCRPress the Menu button. The screen shown below will appear Press the PLAY/ button or the STOP/ button to select Language SelectionPress the Menu button English or Español Spanish Press the STATUS/EXIT buttonAutomatic Channel Setup Wait for the TV/VCR to set up channelsAdding/Deleting Channels Programming of the channel you added or deleted will appearPress the STATUS/EXIT button once or twice Setting the Clock Manual Clock SettingSetting the Clock cont’d Automatic PBS Channel Selection Wait for the TV/VCR to find the time Message appears, turn off the TV/VCR for a few minutes. WhenManual PBS Channel Selection NOW Searching flashes on the TV/VCR screen Daylight-Saving Time Time Zone Press the Menu buttonFront Panel ANTenna Jack AC Power CordRear Panel Antenna HoleRemote Control Buttons Channel / Buttons Volume / ButtonsALT. CH Alternate Channel Button Mute ButtonAdjusting the Picture Controls More brilliant Adjusting the Picture Controls cont’dDecrease Increase SofterIf you select Status ON, then select Counter only on On-Screen Status DisplaysIf you select Status ON, then select Counter only OFF If you select Status OFFReminder Playing Press the RECord/OTR button once to start recording RecordingGiven below Recording options are on pages 30One-Touch Recording OTRRerecording Tape Duplication Different brands of equipment may operate differentlyAudio and video cables are not included Timer Recording DailyTimer Recording cont’d Instructions continue onPlease see page 48 for more Helpful Hints Checking or Clearing Timer Recordings Defeat Recording Follow the steps below to prevent accidental recordingSetting the Sleep Timer If the power fails, you might lose the sleep timer settingMenu Closed CaptionExample ScreenClosed Caption cont’d Standard Closed CaptionsHalf-screen text Volume Bar PRIM. SETUP. Then, press the F.FWD/ B buttonRepeat Play Over again VCR SETUP, then press the F.FWD/ B buttonB Repeat Play Insert a tape in the TV/VCR Press the Menu buttonRepeat Play cont’d Flashing a will become a flashing BReal-Time Counter Memory Appear on-screenAutomatic Operation Features Super High Speed Searching LP/SLP Playback OptionsForward and Reverse Searching SP/LP/SLP Viewing a Still PictureSpecifications GlossaryHelpful Hints Helpful Hints cont’d Limited Warranty Please contact Philips at French Speaking English SpeakingModel # Serial # Index Supplied Accessories