Philips CCZ192AT, CCZ191AT owner manual Timer Recording cont’d, Instructions continue on

Page 33

CCZ191/CCZ191comb.QX33 4/6/99 6:42 PM Page 33

Timer Recording (cont’d) 33

4

Use the Number buttons (1 - 8) to select a position in which to store the timer recording. Flashing numbers indi- cate an open position (one in which a timer recording has not yet been stored).

NOTE: If you select a number that has already been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on-screen for a few seconds. Then information about the program in that position will appear on-screen. If this happens, press the STATUS/EXIT button. Then use the Number buttons to select another position.

5

●Enter the channel of the TV program you want to record (you must enter a 0 before all single-digit channels).

●If you are recording from line input, press 0, 0. A/V IN will appear on-screen.

●If you are recording using a Cable Box, enter the Cable Box output channel (03 or 04). Be sure to select the channel of the TV program at the Cable Box and leave the Cable Box on for the timer recording.

ONE TIME PROGRAM

PROGRAM 1

CHANNEL – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

6

Press two Number buttons for the hour(s) you want the recording to begin. Press two Number buttons for the minute(s) you want the recording to begin. Press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.

ONE TIME PROGRAM

PROGRAM 1

CHANNEL	10
TIME ON	– – : – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

7

Follow the instructions in step 6 to set the recording’s stop time. (AM or PM will be set automatically.)

ONE TIME PROGRAM

PROGRAM 1

CHANNEL	10
TIME ON	09:30 PM
TIME OFF	– – : – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

Instructions continue on page 34.

4-7

	POWER			SLEEP
		2	3	ALT.CH
	1	2	3
	4	5	6	o
				CHANNEL
	7	8	9	p
		0	+100	o
	SPEED		MUTE	VOLUME
	SPEED		MUTE
				p
		o
		PLAY
o	REW			F.FWD	o
		STOP
		p
	REC/OTR	MEMORY	PAUSE/STILL
				o
	MENU	STATUS/EXIT	CLEAR	TRACKING
	MENU	STATUS/EXIT	CLEAR

p

Helpful Hints

•If the numbers entered do not match the TV/VCR’s calendar, the entry will be rejected and a question mark will appear on-screen.

•To make corrections while you are programming a timer recording, press the CLEAR button until the cursor is flashing on the item you want to change. Then enter the cor- rect information.

Image 33

Contents CCZ191AT CCZ192AT For Customer Use Dear Philips Magnavox product ownerFeatures Safety PrecautionsIntroduction Table of Contents Putting Batteries in the Remote Control Before Using the TV/VCRUsing the Remote Control VCR MaintenanceHooking Up The TV/VCR Hook up your TV/VCR using one of the connections shownANTenna Jack on the TV/VCR Rod AntennaAudio and video cables are not supplied Hooking Up The TV/VCR cont’dBent pin Crooked Pin Straight PinYou cannot set up channels if you are using a Cable Box Turning On the TV/VCRPress the Menu button. The screen shown below will appear Press the Menu button Language SelectionPress the PLAY/ button or the STOP/ button to select English or Español Spanish Press the STATUS/EXIT buttonWait for the TV/VCR to set up channels Automatic Channel SetupAdding/Deleting Channels Programming of the channel you added or deleted will appearPress the STATUS/EXIT button once or twice Manual Clock Setting Setting the ClockSetting the Clock cont’d Automatic PBS Channel Selection Message appears, turn off the TV/VCR for a few minutes. When Wait for the TV/VCR to find the timeManual PBS Channel Selection NOW Searching flashes on the TV/VCR screen Daylight-Saving Time Press the Menu button Time ZoneFront Panel Rear Panel AC Power CordANTenna Jack Antenna HoleRemote Control Buttons ALT. CH Alternate Channel Button Volume / ButtonsChannel / Buttons Mute ButtonAdjusting the Picture Controls Decrease Increase Adjusting the Picture Controls cont’dMore brilliant SofterIf you select Status ON, then select Counter only OFF On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status OFFReminder Playing Given below RecordingPress the RECord/OTR button once to start recording Recording options are on pages 30OTR One-Touch RecordingRerecording Tape Duplication Different brands of equipment may operate differentlyAudio and video cables are not included Daily Timer RecordingInstructions continue on Timer Recording cont’dPlease see page 48 for more Helpful Hints Checking or Clearing Timer Recordings Follow the steps below to prevent accidental recording Defeat RecordingIf the power fails, you might lose the sleep timer setting Setting the Sleep TimerExample Closed CaptionMenu ScreenClosed Caption cont’d Standard Closed CaptionsHalf-screen text PRIM. SETUP. Then, press the F.FWD/ B button Volume BarRepeat Play B Repeat Play VCR SETUP, then press the F.FWD/ B buttonOver again Insert a tape in the TV/VCR Press the Menu buttonFlashing a will become a flashing B Repeat Play cont’dAppear on-screen Real-Time Counter MemoryAutomatic Operation Features Forward and Reverse Searching SP/LP/SLP Playback OptionsSuper High Speed Searching LP/SLP Viewing a Still PictureGlossary SpecificationsHelpful Hints Helpful Hints cont’d Limited Warranty Please contact Philips at French Speaking English SpeakingModel # Serial # Index Supplied Accessories