Philips VRB413AT, VRB613AT owner manual Setting the Remote to Operate a TV

Page 21

Setting the Remote to Operate a TV 21

Your VCR remote control may operate your TV. If the remote	Find your
control doesn’t operate your TV now, follow the steps below.	1&6 2TV code.

1

Point the remote control at your TV and press the TV button. Then, press the POWER button. If your TV turns on or off, try the other TV buttons (see pages 23-24). If your TV doesn’t turn on or off, or if the other buttons don’t work, go to step 2.

2

4


POWER	VCR/TV	EJECT

VCR

TV

CBL/DBS

	PLAY
REW		F.FWD
	STOP
MENU	STATUS/EXIT	CLEAR

Find the brand of your TV on the list below, and remem- ber the two-digit number beside it.

TV CODES

EMERSON	. . . . . .14	PHILCO	. . . . . .14
FISHER	. . . . . .11	PHILIPS	. . . . . .01
GE	. . . . . .10	PHILIPS MAGNAVOX.	.01, 02, 03
GOLDSTAR	. . . . . .04	QUASAR	. . . . . .07
HITACHI	. . . . . .12	RCA	. . . . . .10
JVC	. . . . . .05	SAMSUNG	. . . . . .17
MAGNAVOX	01, 02, 03	SANYO	. . . . . .11
MARANTZ	. . . . . .13	SEARS	. . .08, 11
MITSUBISHI	. . . . . .13	SHARP	. . . . . .16
MONTGOMERY WARD . . . .14		SONY	. . . . . .09
PANASONIC	. . . . . .07	TOSHIBA	. . . . . .08
PANASONIC-GAOO .	. . . . . .07	ZENITH	. . .06, 15

5

1 2 3

4 5 6

7 8 9

ENTER	ALT. CH
	0
SPEED	TIME SEARCH PAUSE/STILL

REC/OTR MEMORY SLOW

CH

VOL

MUTE3

3

Press the MUTE button.

4

Within 30 seconds, press the TV button.

5

Within 30 seconds, press the Number buttons to enter the two-digit code for your TV brand. For example, if you have a Zenith TV, press Number buttons 0, 6.

6

Repeat step 1. If the remote control works your TV, you’re fin- ished. If the remote control still doesn’t work your TV, repeat steps 3-5, using a different code for your brand (if available).

There is no guarantee that the

remote will work your TV.

Helpful Hints

•The remote control may only operate some features of your TV. For exam- ple, the remote control may turn on the TV power, but it may not change channels at the TV.

•If you can not change the channels at the TV using the Number but- tons, press the ENTER button after you press the Number buttons. It may change channels at the TV.

•When you replace the batteries in the remote control, you must pro- gram the remote control again.

•Remember to point the remote con- trol toward the TV during steps 1-6.

Image 21

Contents VRB413AT VRB613AT For Customer Use Dear Philips product ownerThis bolt of lightning indi- cates uninsulated material Model No Serial NoSafety Precautions FeaturesIntroduction Declaration of ConformityTable of Contents Before Using Your VCR Disconnect the antenna or cable from your TV Hookups without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups without a Cable Box/Direct Broadcast System cont’dHookups with a Cable Box/Direct Broadcast System ConnectionsRecording/Viewing Any Channel Cable Signal Cable Box/DBS Recording One Channel/Watching AnotherTV’s Antenna Hookups with a Stereo TV VRB613VRB413 Turning on Your VCR Press the VCR button, then press the Power button2Turn on the TV Press the Menu button. The display shown below will appearAutomatic Channel Setup Press the VCR button Press the Menu buttonVRB613 only Automatic Channel Setup cont’d Adding/Deleting ChannelsPress the STATUS/EXIT button Press the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsSetting the Clock Manual Clock SettingDo each step within 60 seconds of the previous step Enter a 0 before a single-digit number Setting the Clock cont’dPress the VCR button, then press the Menu button Automatic Clock SettingTime Zone Press the VCR button Daylight-Savings TimeLanguage Selection Your VCR remote control may operate your TV. If the remote Setting the Remote to Operate a TVYour code 2FindVOLume o/p Button Press to adjust the volume of your TV Remote Control ButtonsEject Button VCR ButtonRemote Control Buttons cont’d TV ButtonPress to operate the TV Status Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Timer LightCassette Compartment VCR LightFWD Fast Forward Button Power ButtonRemote Sensor REWind ButtonRear Panel VHS Quasi Play Back Sqpb PlayingRead and follow the steps below to play a tape 1Turn on the TV 2Insert a tape in the VCRIf the VCR light appears on the display panel, go to . If RecordingVCR light does not appear, press the VCR/TV button once RECord light will appearRecording One Channel/Watching Another OTR CH12 One-Touch RecordingDaily Timer RecordingTime OFF To Correct Push Clear To END Push Exit Timer Recording cont’dTape Speeds Press the STATUS/EXIT button. Program WAS COMChecking or Cancelling Timer Recordings RF coaxial cable Rerecording Tape DuplicationVCR SET UP, then press the F.FWD/B button Repeat PlayPress the F.FWD/B button so that on appears beside Press the STATUS/EXIT button to see the status display Real-Time Counter MemoryPress the VCR button Press the Time Search button Time SearchForward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Understanding On-Screen Displays Specifically…Monitor Press the RECord/OTR button to start recording Multi-Channel Television Sound System VRB613 only cont’dHi-Fi Stereo Sound System VRB613 only Blue Background Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Renewed Index Page Page Page Supplied Accessories