Philips VRB413AT Real-Time Counter Memory, Press the STATUS/EXIT button to see the status display

Page 39

Real-Time Counter Memory 39

Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later.

1

Press the VCR button.

2

POWER VCR/TV EJECT

Play, fast forward, or rewind a tape to the location that you would like to refer to later. Press the STOP/p button to stop the tape.

3

1

2

VCR

REW

MENU

TV

CBL/DBS

PLAY

F.FWD

STOP

STATUS/EXIT

CLEAR

6

4

Press the STATUS/EXIT button to see the status display.

STOP	1:08PM
TV STEREO	CH10

3

1

4

2 3

5 6

CH

STEREO

VRB613 only

SLP 1 : 23 : 45 HIFI

4

While the status display is on the screen, press the CLEAR button to reset the real-time counter to zero.

STOP	1:08 PM
TV STEREO	CH10

STEREO

VRB613 only

SLP 0 : 00 : 00 HIFI

5

While the real-time counter is on the screen, press the MEMORY button so that M appears beside the counter.

STOP		1:08 PM
TV STEREO		CH10
		STEREO
						VRB613 only
SLP M 0 : 00 : 00		HIFI

6

To go to a tape location where the real-time counter was reset to zero, press the REW(ind)/{ button or the F.FWD/B button when playback is stopped.

When the tape reaches the point at which the counter was set to zero, the tape will stop.

Press the PLAY/o button to watch the tape.

7 8 9

ENTER

ALT. CH

0VOL

SPEED TIME SEARCH PAUSE/STILL

REC/OTR MEMORY SLOW MUTE

5

Helpful Hints

•The MEMORY button does not function if REPEAT PLAY is set to ON. Details are on page 38.

•To erase a real-time counter memo- ry, press the MEMORY button until the M disappears from the screen.

•You may only set the real-time counter to zero at one location at a time. If you set the real-time counter to zero at a second loca- tion, the previous real-time counter to zero setting will be erased.

Image 39

Contents VRB413AT VRB613AT Model No Serial No Dear Philips product ownerFor Customer Use This bolt of lightning indi- cates uninsulated materialDeclaration of Conformity FeaturesSafety Precautions IntroductionTable of Contents Before Using Your VCR Disconnect the antenna or cable from your TV Hookups without a Cable Box/Direct Broadcast SystemPlug in the TV and the VCR Hookups without a Cable Box/Direct Broadcast System cont’dHookups with a Cable Box/Direct Broadcast System ConnectionsRecording/Viewing Any Channel Cable Signal Cable Box/DBS Recording One Channel/Watching AnotherTV’s Antenna Hookups with a Stereo TV VRB613VRB413 Press the Menu button. The display shown below will appear Press the VCR button, then press the Power buttonTurning on Your VCR 2Turn on the TVAutomatic Channel Setup Press the VCR button Press the Menu buttonVRB613 only Automatic Channel Setup cont’d Adding/Deleting ChannelsPress the STATUS/EXIT button Press the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsSetting the Clock Manual Clock SettingDo each step within 60 seconds of the previous step Enter a 0 before a single-digit number Setting the Clock cont’dPress the VCR button, then press the Menu button Automatic Clock SettingTime Zone Press the VCR button Daylight-Savings TimeLanguage Selection Your VCR remote control may operate your TV. If the remote Setting the Remote to Operate a TVYour code 2FindVCR Button Remote Control ButtonsVOLume o/p Button Press to adjust the volume of your TV Eject ButtonRemote Control Buttons cont’d TV ButtonPress to operate the TV If you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only onVCR Light Timer LightVCR Display Panel Cassette CompartmentREWind Button Power ButtonFWD Fast Forward Button Remote SensorRear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingVHS Quasi Play Back Sqpb Read and follow the steps below to play a tapeRECord light will appear RecordingIf the VCR light appears on the display panel, go to . If VCR light does not appear, press the VCR/TV button onceRecording One Channel/Watching Another OTR CH12 One-Touch RecordingDaily Timer RecordingTime OFF To Correct Push Clear To END Push Exit Timer Recording cont’dTape Speeds Press the STATUS/EXIT button. Program WAS COMChecking or Cancelling Timer Recordings RF coaxial cable Rerecording Tape DuplicationVCR SET UP, then press the F.FWD/B button Repeat PlayPress the F.FWD/B button so that on appears beside Press the STATUS/EXIT button to see the status display Real-Time Counter MemoryPress the VCR button Press the Time Search button Time SearchViewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Understanding On-Screen Displays Specifically…Monitor Press the RECord/OTR button to start recording Multi-Channel Television Sound System VRB613 only cont’dHi-Fi Stereo Sound System VRB613 only Blue Background Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Renewed Index Page Page Page Supplied Accessories