Dlp-Tv

Wiring: A send module (US-P3 or US-V3) needs to be connected to a Knoll receive module (UR-

P3 or UR-V3) to work correctly. The send and receive module are connected using

a single cat 5 wire using all 8 conductors. Connection is made with the RJ45 connector (RJ45 plug not supplied). Always use standard cat 5 wiring practices. Using the correct wire pairs and polarity is VERY important.

Connection to stereo video source equipment: Connect the three US-P3 or US-V3 gold RCA jacks with a good quality gold connector triple wire component RCA jumper cable to the appropriate three component output jacks on your DVD, dish receiver, D-VHS, VCR, stereo or other equipment.

If there is a switched outlet on your output equipment, you may want to plug the PS1202 power supply to the switched outlet.

Make sure a good quality RJ45 8-8 crimper is used to connect the RJ45 connector to the cat 5 wire. Poor crimping and mismatched wires are the biggest cause of installation problems.

Power requirements: The Knoll balun system requires a single PS1202 power supply connected to the send unit only. In certain cases with very long leads a higher voltage PS1506 15 VDC power supply may be required if wavy or image video lines are evident.

Connection to the Projector, TV or other components: Connect the three US-P3 or US-V3 gold RCA jacks with a good quality gold connector triple wire component RCA jumper cable to the appropriate three component input jacks on your projector, plasma, TV or other component. Make sure the correct projector, plasma, TV or other component input is selected.

Multiple Connection(s): If the component signal needs to be sent to more than one receiver, this can easily be accomplished by daisy chaining the Knoll component senders. The US-P3 and/or US-V3 sender RCA inputs need to have their three RCA inputs Y-corded together. Each sender is connected via one cat 5 wire to one UR-P3 or UR-V3 receiver (as above). Three resistors in all but one of the senders need to be snipped. For example, if four senders are being Y-corded together, three (not all four) of the US-P3 and/or US-V3 senders need to be opened up and have the three 75 ohm through hole resistors beside the RCA jacks snipped off. Receive units do not have any alterations. Each send unit requires a PS1202 power supply.

To loop from a local source going to a local component (such as a TV) using Y-cords, the three 75 ohm resistors in the send unit MAY need to be snipped.

The Knoll send receive system does not have any user adjustments and is completely automatic. If need be, please call our tech line for details at 1 800 566 5579.

This product may contain lead that some states have determined are harmful. Wash you hands after touching this product.

Decora™ is a trademark of Leviton

DVD Player
	CAT 5
	US-P3
	Power supply
PS1202	gives power
	for UR-V3

UR-V3

Power is supplied by US-V3

US-P3, UR-V3, US3-HUB, US-V3, UR-P3 specifications

Knoll Systems has made significant strides in the audiovisual equipment sector with its cutting-edge product lineup, including the US-V3, US3-HUB, UR-P3, UR-V3, and US-P3 models. Each of these devices is designed to enhance audio and video presentations, integrating seamlessly into various environments, from corporate spaces to educational institutions.

The US-V3 is known for its versatility and high-performance capabilities. It features advanced video processing technologies, providing true-to-life images and seamless transitions between multiple sources. The device supports a range of resolutions, making it compatible with modern displays and projection equipment. With enhanced connectivity options, including HDMI, USB-C, and legacy video ports, the US-V3 ensures compatibility with a variety of devices, making it an ideal solution for environments requiring frequent equipment changes.

The US3-HUB complements the US-V3 by acting as a central connectivity point. It's equipped with multiple input and output ports, allowing users to easily switch between different sources. The hub's intelligent design minimizes cable clutter and streamlines the connection process, enhancing user experience. Moreover, its built-in power management features ensure devices remain charged and ready for use.

The UR-P3 and UR-V3 models are engineered for unified communications, optimizing audio and video quality for remote meetings. These devices utilize advanced sound processing technologies to filter out background noise and ensure clear communication. The UR-P3 is particularly focused on audio, featuring high-quality microphones and speakers that provide an immersive sound experience. Meanwhile, the UR-V3 integrates high-definition video capabilities, with support for 4K resolution and wide-angle lenses, enabling high-quality video conferencing.

Lastly, the US-P3 model offers a robust display solution, integrating touchscreen functionality for interactive presentations. Its intuitive interface allows for easy navigation through various media and applications, enhancing engagement during discussions. The US-P3 also supports wireless connectivity, allowing users to share content effortlessly from their devices.

In conclusion, Knoll Systems’ US-V3, US3-HUB, UR-P3, UR-V3, and US-P3 represent a comprehensive suite of audiovisual solutions, designed to meet the demands of modern communication and collaboration. With their emphasis on connectivity, usability, and high-quality performance, these devices are poised to elevate any presentation or meeting environment. By leveraging advanced technologies and user-centric design, Knoll Systems continues to redefine the standards for audiovisual equipment in diverse settings.