Servo System, Troubleshooting Guide

Servo System

The Power Plant provides a virtual Servo System to continually correct for any DC offset. This will reduce hum from problematic or sensi- tive transformers as the Power Plant produces pure AC waveforms indefinitely without the need for calibration.

Troubleshooting Guide

The Power Plant P500 sets a new mark for performance and protection. It has been designed to bring forth the absolute best from the connected equipment. In addition to the audio and video improvements, the P500 will also provide long-term product reliability and the piece of mind that connected equipment is safe from electrical disturbances.

In the event of abnormal operation with the P500, please refer to the following suggestions:

Unit will not turn on

1.Check the obvious. Is it plugged in and is the AC wall outlet live? This can easily be tested by using a functional lamp. Plug the lamp into the wall outlet and see if the light works. If not, the P500 may be plugged into a switched outlet, or perhaps the circuit breaker feeding the outlet has tripped and needs resetting.

2.After plugging the unit into the wall, the display will read

"WAIT" for several seconds to initialize its circuitry. The P500 will only become activated after pressing the front panel power button. Be sure that the unit is both plugged into the wall and turned on by the front panel power button.

3.Check the Main Fuse. The chances of the Power Plant’s main fuse being blown are very remote. However, if the Main Fuse is blown, the P500 will be completely inoperable. To check the fuse locate the section of the back panel labeled "Main Fuse." Unplug the unit from the wall, remove the fuse and check its conductivity. If necessary, replace the fuse and

try powering up the P500. If the main fuse is blown and a replacement fuse does not solve the problem, please contact your dealer for additional service.

The Regenerator outlets are passing AC, but the Filtered AC outlets are not functioning Check the Protection Fuse. To check the fuse locate the section of the back panel labeled "Protection Fuse." Unplug the unit from the wall, remove the fuse and check its conductivity. If necessary, replace the fuse and try powering up the P500. If the Filtered AC outlets still do not pass AC, please contact your dealer for additional service.

The P500 seems to be working, but the display is blank

The P500 may be in the display blanking mode. Press the Mode Up or Down buttons on the front panel and the display should turn back on.

My turntable or fan based equipment is not operating normally.

Any turntable or equipment with AC synchronous fans should not be used with MultiWave II or AutoWave. These products must be used with 60Hz SINE mode or be plugged into the Filtered AC outlets.

The display is flashing "HOT!"

The P500 will turn itself off and flash "HOT!" on the display if it detects an internal temperature that exceeds safe operating limits. The internal cooling system will continue to operate until the temperature has been reduced to a safe limit.

can be adjusted in 1 hertz increments from 50Hz to 120Hz by using the Edit Up and Edit Down buttons. The default setting is 60Hz.

The frequency setting will only be displayed if the Waveform menu is set to SINE.

Voltage produced

This mode will display the output voltage of the Power Plant at the Regenerated AC outlets. The output voltage can be adjusted in 1 volt increments by using the Edit Up and Down buttons. The range varies depending on the Power Plant model:

•100 volt model ranges from 95 - 105 v Default setting is 100 volts.

•120 volt model ranges from 110 - 125 v Default setting is 117 volts.

•240 volt model ranges from 220 - 240 v

Default setting is 220 volts. (adjustments in 2 volt increments)

As long as the voltage to the Power Plant does not deviate more than 10% below normal it will continue to output the voltage displayed on the front panel.

Wattage produced

This mode will display, in real-time, the wattage the P500 is generating. The P500 is capable of delivering up to 500 watts for short amounts of time, however if over 500 watts is drawn for too long or peak wattage is too large then

the P500 will go into protection mode. The watt meter

will only show the total

wattage produced for the zone labeled Regenerated AC.

Percentage of maximum power output

This mode will display,

in real-time, the percentage of total power currently being used by equipment on the Regenerated AC outlets. This reading will factor the type of load into the percentage of maximum power output. The percentage of maximum power output is not necessarily

proportional to the wattage produced, as it will vary with the type of load.

It is possible that the display will show over 100% for short amounts of time during heavy current draw. This will typically occur during loud or very dynamic passages of music or very bright scenes in video. The P500 will not maintain 100% output power continuously.

Display Blanking

This mode allows discrete front panel operation by blanking the display. The PS logo will continue to illuminate in blue to indicate that the unit is operational.

P500 specifications

The PS Audio P500 is an innovative power plant that stands out in the high-fidelity audio community. This device is designed to enhance the performance of audio components by providing clean, stable, and isolated power. The P500 combines a range of advanced technologies and features that cater to audiophiles seeking to elevate their listening experiences.

One of the primary characteristics of the P500 is its ability to regenerate AC power. Traditional power conditioners merely filter and clean incoming electricity, whereas the P500 goes a step further by creating pure sine wave power from DC. This regeneration process helps to eliminate noise and distortion, ensuring that audio components receive electricity that is both stable and untainted.

The P500 features multiple outlets, allowing users to connect several audio components simultaneously. Each outlet generates electricity that maintains the same high quality, meaning that all connected devices benefit from the P500's advanced technology. This is particularly advantageous for high-end systems with numerous components, as it aids in maintaining optimal performance across the entire audio chain.

Another standout feature of the P500 is its LCD display, which provides vital information about power output and draw. It allows users to monitor the performance of their audio system in real time, enabling them to optimize their setup for the best possible sound quality. This level of monitoring is crucial for audiophiles who take their listening seriously and want to ensure that every detail is perfectly rendered.

Additionally, the P500 includes a built-in isolation transformer, which further protects audio equipment from external electrical interference. This isolation is essential in minimizing the impact of power supply pollution, which can compromise sound quality. With the P500, users can rest assured that their audio components are getting the cleanest power possible.

The design of the P500 also deserves mention. It is built with high-quality materials, featuring a robust chassis that not only looks great but also reduces vibrations that can affect performance. This attention to detail in both engineering and aesthetics makes the P500 a desirable component for any serious audio enthusiast.

In summary, the PS Audio P500 is a powerful tool for audiophiles looking to enhance their systems with superior power management. With features like AC regeneration, multiple high-quality outputs, real-time monitoring, isolation transformers, and a well-built design, the P500 provides an unparalleled listening experience that transforms how music is enjoyed. As a result, it has become a staple among those who demand the very best in audio fidelity.