Omega LVF-210, LVU-150 warranty Electrical, Through Wall Installation, Multi-Point Installation

Page 5

INSTALLATION

Step Five

Through Wall Installation:

Omega’s powered level switches may be installed through the top, side or bottom of a tank wall. The sensor has male 3/4" NPT threads on either side of a 15/16" wrench flat. This enables the user to select the sensor’s mounting orientation, installed outside of the tank in, or inside of the tank out.

Multi-Point Installation:

Omega’s LVM-10 series mounting system is an in-tank fitting which enables users to install up to four OMEGA sensors of any technology, to any depth, along the entire length of track. LVM-10 series may be installed through the top wall of any tank using a standard 2" NPT tank adapter. If no tank top installation is available, Omega's side mount bracket, LVM-30, enables LVM-10 series to be installed directly to the side wall of a tank.

ELECTRICAL

Step Six

Supply Voltage:

The supply voltage to the powered level switch should never exceed a maximum of 36 VDC. Omega controllers have a built-in 13.5 VDC power supply which provides power to all of Omega’s electrically powered sensors. Alternative controllers and power supplies, with a minimum output of 12 VDC up to a maximum output of 36 VDC, may also be used with the powered level switch.

Required Cable Length:

Determine the length of cable required between the powered level switch and its point of termination. Allow enough slack to ensure the easy installation, removal and/or maintenance of the sensor. The cable length may be extended up to a maximum of 1000 feet, using a well-insulated, 14 to 20 gauge shielded four conductor cable.

Wire Stripping:

Using a 10 gauge wire stripper, carefully remove the outer layer of insulation from the last 1-1/4" of the sensor's cable. Unwrap and dis- card the exposed foil shield from around the signal wires, leaving the drain wire attached if desired. With a 20 gauge wire stripper, remove the last 1/4" of the colored insulation from the signal wires.

Signal Outputs (Current sensing):

The standard method used by Omega controllers; this technology uses only two wires (Red and Black). The sensor draws 5 mA when it is dry, and 19 mA when wet. NC/NO status must be set by the controller. The White and Green wires are not used.

Single-Point Installation:

Omega’s LVM-50 series mounting system is an in-tank fitting which enables users to install one OMEGA sensor, of any technology, to a specific depth. The Omega sensor may be installed onto the 3/4" NPT adapter at the end of the LVM-50 series. LVM-50 series may be installed through the top wall of any tank using a standard 2" NPT tank adapter. Omega's side mount bracket, model LVM-30, may also be used if top wall installation is not available.

Red

Shield

Ground

Black

+24 VDC

Power Supply

-

- Multimeter

+ (mA)

Junction

Box

2"

Coupling

Signal Output (Relay switching):

Allows the sensor to switch a small load on or off directly, using an internal 1A relay (60 VAC/60 VDC). Omega’s powered level switch- es features 4 wires (red, black, white and green) and a shield wire. The NO/NC status is set by the polarity of the voltage feeding the red and black wires. The green wire is the common for the relay and the white wire is the NO or NC, depending on the polarity of red and black.

LVM-50

Series

High Level Sensor

LVM-10

Series

Normally Open Wiring:

 

Red

 

Black

Shield

White

Ground

 

 

Green

+24 VDC

-Power Supply

-Multimeter + (Continuity)

Low Level Sensor

Normally Open Wiring:

 

Black

 

Red

Shield

White

Ground

 

 

Green

+24 VDC

-Power Supply

-Multimeter + (Continuity)

Image 5
Contents User’s Guide Table of Common Dielectric Constants SpecificationsDimensions Introduction Safety PrecautionsThrough Wall Installation InstallationMulti-Point Installation Single-Point InstallationWiring the Relay Output WiringWiring to a Omega Controller Wiring as a P-Channel or N-Channel output MaintenanceCleaning Procedure Testing the installation

LVF-210, LVC-152, LVC-100, LTU-101, LVU-150 specifications

The Omega series offers a range of advanced lighting and visualization technologies, including the LTU-101, LVC-100, LVC-152, LVF-210, and LVU-150 models. Each of these products is designed to cater to various industrial, commercial, and residential requirements, showcasing exceptional features, reliability, and innovation.

The Omega LTU-101 is a versatile lighting solution known for its energy efficiency and long lifespan. It employs advanced LED technology to deliver high illumination while consuming minimal power. The LTU-101 boasts a robust design, making it suitable for both indoor and outdoor applications. Additionally, its weather-resistant housing ensures durability in adverse conditions.

Next is the LVC-100, which focuses on providing superior visual clarity and color accuracy. This model is equipped with state-of-the-art optical technologies that enhance the viewing experience in various environments. The LVC-100 can easily be integrated into existing systems, making it a popular choice for commercial use, including retail and presentation settings. Its intuitive controls allow for flexible adjustment of brightness and color temperatures, enhancing user experience.

Moving to the LVC-152, this model excels in versatility and adaptability. Featuring a modular design, the LVC-152 can be customized with different light modules to meet specific lighting needs. This makes it ideal for multifaceted environments such as galleries, museums, or event spaces where dynamic lighting effects are required. The inclusion of smart technologies allows for remote management and programming, aligning well with modern automation systems.

For those seeking robust performance in challenging conditions, the LVF-210 stands out. Built for industrial applications, this fixture is engineered to withstand high levels of dust, moisture, and impact. It employs cutting-edge thermal management technologies to ensure optimal functioning even under extreme workloads, offering a reliable lighting solution for warehouses and manufacturing facilities.

Lastly, the LVU-150 is designed for versatility in both outdoor and indoor settings. Its compact size does not compromise its power, providing bright and uniform illumination. The LVU-150 incorporates intelligent sensors that adjust lighting based on ambient conditions, promoting energy savings without sacrificing performance.

With this impressive portfolio, Omega continually demonstrates its commitment to pushing the boundaries of lighting technology, ensuring a perfect combination of function, form, and efficiency across various applications.