VTech VM321-2 user manual Appendix

Page 41

Appendix

Troubleshooting (continued)

The parent unit plays any sounds from the baby unit and I think it is too noisy.

•You may have set the sensitivity level to Level 5 (Maximum). If you do so, the baby unit will transmit any sounds detected to the parent unit. You may need to adjust the sensitivity level to a lower level (page 23).

•You may need to adjust the speaker volume on the parent unit (page 30).

The parent unit does not play any sound when there is noise from the baby unit.

•Make sure the parent unit is powered up by connecting it to AC power (page 12) or to the rechargeable battery provided (page 10).

•Make sure the parent unit is turned on (page 30) and the speaker volume is not set to off (page 30).

•Make sure the parent unit is not monitoring in multi-CAM mode.

•The parent unit may be too far away from the baby unit. Move the parent unit closer to the baby unit (but not less than 3 feet).

•If the parent unit is powered by the provided battery, make sure there is sufficient charge. Charge the battery in the parent unit for up to 12 hours.

•You may have set the sensitivity level to a very low level. If you do so, the baby unit will not detect sounds that is too soft or light. You may need to adjust the sensitivity level to a higher level (page 23).

•Large obstructions may impact the reception. Try to relocate the baby unit, away from large obstructions such as walls and doors.

•Remove the battery and then install it again. Turn on the baby unit and the parent unit. Allow up to one minute for the parent unit and the baby unit to synchronize.

•Other electronic products may cause interference with your video and audio monitor. Try installing your video and audio monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.

Battery low at the Parent Unit and display on the parent unit.

•Charge the battery in the parent unit for up to 12 hours.

•Remove the battery and then install it again. Use it until fully depleted, then recharge it in the parent unit for up to 12 hours.

•If the above measures do not correct the problem, replace the battery.

35

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Safe & SoundTM Video and audio monitor User’s manual Congratulations Product introduction Important safety instructions Electromagnetic fields EMF Table of contents Getting started Parts checklistBaby unit battery installation Baby unit installation Tabletop to wall mount installation Baby unit installation optionsGetting started Getting started Getting started Getting started Getting started Parent unit battery installation Getting started Parent unit installation Battery low at Parent Parent unit battery chargingBattery indicators Battery status Action Baby unit overview Baby unit lights Parent unit overview Link Parent unit lightsParent unit display screen icons Positioning and operating range Audio settingsPosition the video and audio monitor Operating rangeWaiting for linking Test your video and audio monitor before useTo test your video and audio monitor Alert tone Parent unit settingsUsing the menu To set the no link alert of the parent unit No link alertTo set the sound sensitivity level of the baby unit SensitivityMinimum temperature TemperatureTo set the minimum temperature of the baby unit Maximum temperatureTo set the temperature alert of the baby unit Temperature alertTemperature format To change the temperature scaleLCD brightness VibrationSound-activated screen To pair a baby unit Pair/unpair CAMPair new CAM Unpair CAM LanguageTo unpair a baby unit To change the languageSpeaker volume Power on or off the baby unitBaby unit operation Play lullabiesTo zoom in or out while in single-CAM mode Power on or off the parent unitTo zoom in or out while in multi-CAM mode Parent unit operationTalk to the baby unit ViewTo view different baby units To turn the screen on or offParent unit display screen messages AppendixParent unit battery Video and audio monitor produces high-pitched noise TroubleshootingMy video and audio monitor does not work at all Appendix Parent unit beeps and is not performing normally Light on the parent unit is offCommon cure for electronic equipment Operating range MaintenancePacemaker patients Precautions for users of implanted cardiac pacemakersRbrc seal What does this limited warranty cover? Limited warrantyHow long is the limited warranty period? What is not covered by this limited warranty?Other limitations How do you get warranty service?FCC Part FCC and IC regulationsIndustry Canada RF radiation exposure statementLCD Technical specificationsIndex Index Member of the Vtech Group of Companies 91-004422-030-100

VM321, VM321-2 specifications

The VTech VM321-2 is a state-of-the-art video baby monitor designed to provide parents with peace of mind while keeping an eye on their little ones. This monitor, part of VTech's VM321 series, combines advanced technology with user-friendly features to ensure that caregivers can monitor their child effortlessly.

One of the standout features of the VM321-2 is its high-resolution color video display. The monitor boasts a large screen that provides clear visuals, allowing parents to see their baby in detail. This is particularly useful during nighttime monitoring, as the device is equipped with infrared night vision, enabling parents to keep watch without disturbing the sleeping baby.

Another key aspect of the VM321-2 is its two-way audio communication system. This feature allows parents to not only hear their baby but also communicate with them. The ability to soothe a crying infant from another room is invaluable and helps in comforting babies quickly.

The VM321-2 includes multiple cameras, allowing for coverage in different rooms or angles. Parents can easily switch between cameras or view multiple perspectives on the same screen, ensuring they are always aware of their child’s surroundings. The monitor also offers a wide-angle lens, which provides an expansive view of the nursery.

In terms of range, the VM321-2 is impressive, with a reliable connection over a significant distance. The monitor operates on a secure digital frequency, minimizing interference from other devices in the home. This means that parents can move freely throughout their house while still maintaining a clear and uninterrupted connection with their baby.

Additional features include temperature monitoring, which alerts parents if their baby's room is too hot or cold, ensuring a comfortable environment. The device also comes with preloaded lullabies and soothing sounds, which can help in calming the baby to sleep.

In summary, the VTech VM321-2 is packed with features that prioritize safety, convenience, and connectivity. Its high-resolution video, two-way audio, extensive range, and additional monitoring features make it a valuable tool for modern parents. With this monitor, families can feel secure knowing they are always connected to their little ones, no matter where they are in the house.
Top Page Image Contents