AMX UDM-RX02 quick start Configuration, Rear Panel Components, Compatibility, UDM Hub Port RJ45

Page 1

Quick Start Guide

UDM-RX02Endeleo Multi-Format Receiver

Overview

Installed at the display device, the UDM-RX02 (FG-UDM-RX02) converts the signal received from a UDM Multi-Format Distribution Hub to standard A/V signals (FIG. 1).

Configuration

The UDM-RX02 is configured via the UDM Hub’s WebConsole. Refer to the UDM Hub’s Operation/Reference Guide for details.

Rear Panel Components

All of the connectors and ports are located on the rear panel (FIG. 2):

 

 

UDM HUB port (RJ45) - from an

Composite (Pr) port

 

 

Composite (Pb) port

 

 

“OUTPUT” port on the UDM-0102

Composite (Y) port

 

 

 

 

VGA (HD15) port

 

 

 

 

 

 

 

 

 

 

 

S-Video port

 

 

 

 

 

 

 

 

CVBS port

 

 

 

 

 

 

FIG. 1 UDM-RX02

 

 

 

Serial port (RJ12)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

With all the same features of the UDM-RX01, the UDM-RX02 adds support for “Common” mode sync, as well as remote power for long cable distance runs.

Compatibility

The UDM-RX02 is compatible for use with the following UDM Hubs:

•UDM-0102 (FG-UDM-0102) - This hub supports Common Synch Mode.

•UDM-0404 (FG-UDM-0404) - This hub supports Common Synch Mode.

•UDM-1604 (FG-UDM-1604C) - This hub supports Common Synch Mode.

•UDM-1604 (FG-UDM-1604) - This hub does not support Common Synch Mode. In this case, the UDM-RX02 will function, but without Common Synch Mode.

Product Specifications

UDM-RX02 Specifications

Power Requirements:

 

24VDC @ .75A

 

 

Note: In most cases the UDM-RX02 is remotely powered

 

 

by the UDM Multi-Format Distribution Hub (see Powering

 

 

on the UDM-RX02).

 

 

 

Rear Panel Connectors:

 

 

 

Power Socket:

 

2.1mm barrel-style DC power socket (female)

 

 

 

UDM Hub (RJ45)

 

Provides audio/video transport as well as control via Cat5,

Port:

 

Cat5e or Cat6 to an UDM Hub.

 

 

 

Serial (RJ12) port:

 

Enables an administrator to control the various functions

 

 

to the UDM-RX02 from a command line prompt and termi-

 

 

nal connection.

 

 

• Requires a DB9-to-RJ12 adapter cable (FG-RS01) to

 

 

connect to a PC.

 

 

• 9600, 8 bit, No Parity, 1 Stop Bit

 

 

 

IR Rx Port:

 

3.5mm stereo input port, for connection of an IR receiver

 

 

to allow setup of the UDM-RX02, local compensation

 

 

controls, and remote control of centrally located IR

 

 

devices.

 

 

 

IR Tx Port:

 

3.5mm stereo IR Transmitter output port allows one IR-

 

 

controlled device (such as a DVD or VCR player) to be

 

 

controlled via optional wired IR emitter.

 

 

 

Audio Connectors:

 

• Black RCA female connector - Digital audio

 

 

• White RCA female connector - Analog audio Left

 

 

• Red RCA female connector - Analog audio Right

 

 

 

Video Connectors:

 

• Yellow RCA female connector - CVBS (supports

 

 

composite video)

 

 

• S-Video - S-video female connector

 

 

• VGA - HD15 female connector (supports VGA video)

 

 

• Green RCA female connector - Component output: Y

 

 

• Blue RCA female connector - Component output: Pb

 

 

• Red RCA female connector - Component output: Pr

 

 

 

Operating Environment:

 

• 35°F - 95°F (5°C - 35°C)

 

 

• Max. relative humidity - 85% (non-condensing)

 

 

 

Dimensions (HWD):

 

1" x 8 15/16” x 3 3/8” (25 mm x 227 mm x 85 mm)

 

 

 

Weight:

 

1.45 lb. (658 g)

 

 

 

Certifications:

 

• CE

 

 

• FCC part 15 Class A

 

 

 

Other AMX Equipment:

 

• RS232 DB9/RJ12 Connection Cable (FG-RS01)

 

 

• UDM-RC02 Multi-Format IR Remote Control

 

 

(FG-UDM-RC02)

 

 

• IR01 IR Emitter Module (FG-IR01)

 

 

• IR03 External IR Receiver Module (FG-IR03)

 

 

• UDM-PS 24VDC, 750mA Power Supply (FG-UDM-PS)

 

 

 

IR Rx port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RCA audio

IR Tx port

 

 

 

 

 

 

 

 

(left/right)

 

 

 

 

Power connector

 

 

SPDIF female Digital Audio port

 

 

FIG. 2 UDM-RX02 - rear panel components

UDM Hub Port (RJ45)

The UDM-RX02 connects to a UDM Hub through a Cat 5/Cat 6 connection. Refer to the UDM Hub’s Operation/Reference Guide for details.

Serial Port

The Serial port is available for diagnostic and troubleshooting purposes.

The Serial port on the UDM-RX02 is an RJ12 connector, and requires a DB9-to-RJ12 adapter cable (FG-RS01) to connect to a PC for Terminal control.

IR Receiver (IR Rx) Port

The IR Rx port is used to enable user control and the remote compensation of the video link to the UDM, using the FG-UDM-RC10 and the FG-IR03.

Refer to the Protocols and IR Learning section of the UDM Hub’s Operation/Reference Guide for details for information on learning a device’s IR commands.

IR Transmit (IR Tx) Port

The IR Tx port issues IR commands from the UDM-RX02 to a controlled display device (TV monitor or display). One IR display device can be connected to the UDM- RX02 via the IR Tx port, and controlled via the UDM Hub’s WebConsole or via remote control.

Connecting an IR Device to the IR Tx Port

1.Connect an IR01 Endeleo IR Emitter Module (FG-IR01) to the IR Tx port on the UDM-RX02.

Note: Ensure the position of the device corresponds to the position assigned in the Devices option of the UDM- Hub’s WebConsole.

2.Run the other end of the IR Emitter cable to the device’s IR sensor, and attach the IR Emitter to the device’s sensor by removing the cover on the reverse side of the IR Emitter.

IR commands for each device on the system have to be learned by the UDM-0102 in order to function properly. Refer to the Protocols and IR Learning section of the UDM Hub’s Operation/Reference Guide for information on learning a device’s IR commands.

AUDIO Connectors

The UDM-RX02 provides standard Audio RCA output connectors for S/PDIF for digital audio, and LEFT/RIGHT for analog audio output (FIG. 2).

VIDEO Connectors

VGA Input at Display Device

1.Attach one end of the VGA cable to the VGA connector on the UDM-RX02.

2.Run the other end to the VGA connector on the display device. Connect firmly.

3.If appropriate connect audio to the audio connectors on the UDM-RX02.

Note: Ensure the UDM Hub port the RX02 is attached to is configured correctly within the Hub’s configuration software. Also ensure the correct Audio Type (Analog L/R, S/PDIF, or None) is selected for the relevant input.

Composite Input at Display Device

1.Attach the composite cable (normally yellow) to the CVBS connector on the UDM-RX02.

2.Run the other end of the composite cable to the Composite connector (normally yellow) on the display device. Connect firmly.

3.If appropriate connect audio to the audio connectors on the UDM-RX02.

SVideo Input at Display Device

1.Attach the SVideo cable to the 4-pin S Video connector on the UDM-RX02.

2.Run the other end of the SVideo cable to the SVideo connector on the display device. Connect firmly.

3.If appropriate connect audio to the audio connectors on the UDM-RX02.

Page 1 Page 2
Image 1
Page 1 Page 2
Contents Product Specifications ConfigurationAudio Connectors Video ConnectorsConnecting an External IR Receiver Module Audio & Video Formats/Resolutions/DistanceConnecting the UDM-RX02 Receiver to the UDM Hub Powering on the UDM-RX02

UDM-RX02 specifications

The AMX UDM-RX02 is a cutting-edge solution designed to cater to modern audio-visual integration needs. As part of the renowned AMX product line, this device is engineered to deliver exceptional performance and versatility in a variety of settings, including commercial and residential environments.

At the core of the UDM-RX02's functionality is its support for 4K video signals, ensuring that users can enjoy high-resolution content without compromising on quality. This capability is complemented by HDCP 2.2 compliance, which secures content protection, making it an ideal choice for settings where copyrighted material is used. The device also features video scaling technology, allowing seamless adaptation of various input signals to the required output format, thus enhancing compatibility across different devices.

One of the standout features of the UDM-RX02 is its capability to handle multiple video sources simultaneously. With its robust switching capabilities, users can switch between various HDMI sources effortlessly, which is essential in environments like conference rooms or home theaters. The device boasts multiple HDMI inputs and outputs, facilitating easy connectivity to various devices such as cameras, laptops, and displays.

In addition to its video processing prowess, the UDM-RX02 integrates advanced audio features. It supports multi-channel audio formats, ensuring that users can experience high-quality sound that complements their visual content. The unit includes audio extraction capabilities, allowing audio to be routed separately from video, which is particularly useful for installations that require dedicated audio systems.

The UDM-RX02 also emphasizes user experience with its intuitive web-based user interface, simplifying management and configuration. Installers and end-users can easily navigate the settings, making adjustments, and monitoring performance without the need for specialized training. Furthermore, its integration with existing AMX control systems provides enhanced functionality, allowing for automated control of multiple devices through a single interface.

In terms of durability, the UDM-RX02 is built with high-quality components that ensure reliable operation over time. Its compact design allows for easy installation in various environments, whether mounted in a rack or installed behind a display.

In conclusion, the AMX UDM-RX02 stands out as a versatile, high-performance device that meets the demands of contemporary audio-visual installations. With its support for 4K video, advanced audio features, multiple input/output options, and user-friendly interface, it is an ideal solution for anyone looking to elevate their audio-visual experience.
Top Page Image Contents