Wiring the AXR-RF, Installing the AXR-RF

If you install the AXR-RF farther away from the Central Controller than recommended in the Wiring Specifications table, an auxiliary ±12 VDC power supply is required for operation.

Wiring the AXR-RF

The AXR-RF uses a rear 4-pin AXlink connector for power and data. Power can be supplied by Central Controller's AXlink cable, or with an optional auxiliary ±12 VDC power supply.

Using the AXlink 4-pin connector for data and power

Connect the Central Controller's AXlink connector to the AXlink connector (male) on the rear panel of the AXR-RF for data and ±12 VDC power.

PWR (+)

AXP

Central Controller

AXM

GND (-)

AXR-RF (3.5 mm connector)

FIG. 3 AXlink wiring diagram

Using the AXlink 4-pin connector with an external ±12 VDC power supply

Use an auxiliary ±12 VDC power supply when the distance between the Central Controller and AXR-RF exceeds the limits described in the Wiring Specifications table. To use an external power supply, connect the Central Controller's AXlink connector to the AXlink connector on the rear of the AXR-RF, as shown in FIG. 4..

PWR (+)

12 VDC power supply

GND (-)

PWR (+)

AXP

Central Controller

AXM

GND (-)

AXR-RF (3.5 mm connector)

FIG. 4 AXlink and 12 VDC power supply wiring diagram

CAUTION: Do not connect the wire from the PWR (+) terminal on the Central Controller to the PWR (+) terminal on the AXR-RF when you connect an external power supply. Do not connect power to the AXR-RF until the wiring is complete.

Connect only the GND (-) wire on the AXlink connector when using an auxiliary ±12 VDC power supply. Do not connect the PWR (+) wire to the AXlink connector's PWR (+) terminal on the Central Controller side of the connector.

Installing the AXR-RF

1.Set the device DIP switch to assign an AXlink device code to the unit.

2.Install the wiring for the AXlink bus.

3.Position the AXR-RF in the location where it will be used. Place the receiver close to, or in the middle of, the area to be covered. It is recommended that you mount the unit where the antenna is away from metal obstructions.

4.Extend the antenna vertically for best reception. If it is necessary to place the antenna in a remote position, use up to 6 ft. (2 m) of RG-174 coax cable.

5.Connect the AXR-RF to the Central Controller with the AXlink cable.

NOTE: To avoid potential problems with Axcess processing, do not install two or more AXR-RF devices, using the same RF frequency, in one system. The AXR-RF is available in frequencies other than 418 MHz (on request).

6.Locate the green AXlink LED on the front panel and verify that it flashes once per second. If so, the AXR-RF is communicating properly with the Central Controller system.

If the LED is on and not flashing, disconnect the AXlink connector and recheck all AXlink wiring connections. Reconnect the AXlink connector to the AXR-RF and verify the LED is flashing once per second.

AMX Corporation reserves the right to alter specifications without notice at any time.

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0913 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

AXR-RF specifications

The AMX AXR-RF is a cutting-edge device designed for professional audio-visual systems, offering exceptional performance and a suite of advanced features. This RF (Radio Frequency) communication device is the latest development in AMX's commitment to delivering innovative solutions for seamless control and connectivity in both large and small environments, including corporate, educational, and entertainment venues.

One of the standout features of the AMX AXR-RF is its ability to provide robust, reliable wireless communication. With a frequency range that minimizes interference, users can expect clear and consistent audio transmission. This is particularly crucial in dynamic environments where multiple devices are in operation, ensuring that data is transmitted without dropouts or delays.

Another key technology integrated into the AXR-RF is its advanced encryption capabilities. Security is paramount in any AV setup, especially in corporate settings where confidential information may be presented. The AXR-RF uses sophisticated encryption protocols to protect the data being transmitted, providing peace of mind to users and administrators alike.

The device is also equipped with a long-range capability, facilitating communication over significant distances without loss of signal quality. This makes it an ideal solution for large venues, such as auditoriums or conference halls, where distances between devices may vary greatly.

User customization is a notable characteristic of the AMX AXR-RF. With an intuitive interface, users can easily adjust settings to suit specific needs, from frequency selection to output power. This level of customization ensures that the device can adapt to different environments, providing optimal performance regardless of the setup.

Furthermore, the AXR-RF supports integration with a variety of AMX control systems, allowing for seamless operation across multiple platforms. This makes it an invaluable component in complex systems, where coordination between different devices is essential.

In summary, the AMX AXR-RF stands out in the market for its advanced features, including reliable wireless communication, robust security protocols, long-range capabilities, and user customization options. With its ability to integrate easily into existing AMX ecosystems, it is poised to enhance audio-visual experiences across diverse applications, setting a new standard in wireless AV communication technology.