Graco 44164, 44339 manual Harness Straps fig. a, Harness Tie fig. b, Buckle Point Models

Page 20

OPERATIONS and ADJUSTMENTS

1HarnessStraps(fig.a):

•To tighten: Slide harness lock open to lift adjuster bar. Pull harness straps down until all slack is removed. (page 21, fig. a-e)

•To loosen: Slide harness lock closed to remove straps from harness plate and adjuster bar. (page 21, fig. a-e)

HarnessTie(fig.b):

•To open: Unhook harness tie as shown.

•To close: Fasten harness clip. Position harness clip at middle of child’s chest, level with armpits.

2Buckle:

5-Point Models

•To buckle: Insert both tongues into buckle. Pull up on tongues to be sure they are locked.

•To unbuckle: Press red button and pull tongues out of buckle.

3OverheadShieldModels

MUST be in opening closest to but not under child.

•To buckle: Push tongue into opening. Pull up on tongue to be sure it is locked.

•To unbuckle: Press red button, pull tongue out of opening and lift shield

18over top of car seat.

4Recline/UprightPositions(fig.c:):Rear-facing- MUST use Recline position.

Forward-facing - MUST use Upright position

•Upright Position: Rotate stand out and push into car seat.

•Recline Position: Pull stand out and rotate into car seat.

55-PointCrotchStrapAdjustment(fig.d):

MUST be in opening closest to but not under child.

•From bottom of car seat, pull crotch strap clip out and remove clip from crotch strap loop.

•From top of car seat, pull crotch strap out and thread through desired slot. Make sure red button is facing away from child.

•From bottom of car seat, re-attach clip to crotch strap loop exactly as shown.

Page 19 Page 21
Image 20
Page 19 Page 21
Contents 44164 Table of Contents Registration Information Safety First Check ListImportant Information Do not use rear-facing child Replaced. do not use it again! a Unoccupied Car Seat Warm Weather Basic InformationVehicle Seat Protection What is LATCH? Latch System for VehiclesVehicle Top Tether Anchor Points Lower Anchor Vehicle Seat CreaseLatch System Only use LatchVehicle Lower Anchor Points Car Seat Top Tether BeltHeight & Weight Limits Preterm or Low Birth Weight InfantsRear-facing 5 to 22 lbs .3-10 kg Forward-facing 20 to 40 lbs to 18 kgREAR-FACINGINSTALLATION with Vehicle Seat Belts Latch storage Under pad Openings Towels Fig. dFORWARD-FACING Installation with Vehicle Seat Belts Stand Fig. eREAR-FACINGINSTALLATION with Latch Openings Towels Fig. eFORWARD-FACING Installation with Latch FORWARD-FACING Installation with Latch Tether Strap Openings Pull to tighten StandOverhead Shield Models Only Placing Child in CAR SeatPoint Models Only Placing Child in CAR Seat Buckle Point Models Harness Straps fig. aHarness Tie fig. b Harness Lock Adjuster Bar Upright ReclineChanging Harness Strap Slots To adjust harness strapsOverhead Shield Adjustment fig. f ModelsAll Latch Belt Routing Rear-facing openingRemoving Latch from Vehicle Anchor Points Fig. jLatch storage Fig. mVehicle Seat Belts Vehicle Seat Belts Belts Forward of Seat CreaseFlip Lap Belts Manually AdjustableLap Belts With Retractor Passive Restraint Lap Belt with Motorized Shoulder Belt Passive Restraint Lap or Shoulder Belt Mounted on DoorPull Combination Lap/Shoulder Belt with Sliding Latch PlateCombination Lap/Shoulder Belt with Locking Latch Plate Locking Clip Additional Information Tether StorageFor storage of tether hook Tether Hook Back of Car SeatBack of seat Seat Pad and Overhead Shield Pad Harness StrapsShell BuckleAircraft Use Second Hand Car SeatPage Parts List How to OrderShip to Both Numbers RequiredCall US First Manual de instrucciones Índice DE Materias PreliminarUtilización Información especialInformación Importante Lista de control de seguridadAdvertencias Prevenga lesiones graves o la muerte Page Información Básica Asientos peligrosos del vehículo¿QUÉ ES EL LATCH? Anclaje Fig. b o Fig. cSistema Latch Sistema LatchCon Latch Únicamente Puntos de Anclaje Inferiores del VehículoLímites DE Altura Y Peso Niños prematuros o de bajo peso de nacimientoAdvertencia Fig. d Fig. a Soporte Instalación Orientada Hacia Atrás CON Latch Aperturas Toallas Instalación Orientada Hacia Delante CON Latch Correa de Anclaje Aperturas Tire para Apretar Soporte Colocar AL Niño EN EL Asiento DE Seguridad Con ModelosbarraProtectora Correas del arnés fig. a Cierre del arnés fig. bHebilla Modelos de 5 puntos Posiciones reclinada / vertical fig. cTraba del arnés Barra de ajuste Clip Vertical ReclinadaNota Los Usar el sistema Latch orientado hacia atrás Orientado hacia atrásSacar el Latch del vehículo puntos de anclaje Almacenaje del Latch Cinturones DE Seguridad DEL Vehículo Cinturones ubicados delante del pliegue del asiento Pliegue del asiento AsientoDéle la vuelta Cinturones de regazo ajustables manualmenteCinturones de regazo con retractor No SE Debe usar con ningún asiento de seguridad Tire Fig. a Déle la vueltaClip de cierre Pulgada 1 cmInformación Adicional Almacenaje del anclajePara almacenar el gancho del anclaje Gancho del anclaje Parte trasera del asientoCuidado y limpieza Retirar la almohadilla de la barra protectoraLas almohadillas del asiento y de la barra protectora Correas del arnésArmazón HebillaUso en aeronaves Asiento de seguridad para automóviles de segunda manoNotas Lista DE Piezas Cómo hacer pedidosEnvíe a Llámenos Primero

44339, 44164 specifications

The Graco 44164 and 44339 are two highly regarded models in Graco's extensive lineup of airless paint sprayers. These sprayers are engineered for both professionals and DIY enthusiasts, offering an efficient solution for various painting projects. Their compact design and high-performance capabilities make them a popular choice among contractors and homeowners alike.

One of the key features of the Graco 44164 is its powerful piston pump, which ensures a consistent and smooth flow of paint. This high-quality pump allows for the use of a wide variety of paint materials, including thicker paints and coatings, without sacrificing performance. The sprayer can handle everything from latex paint to oil-based products, making it versatile for different tasks.

Similarly, the Graco 44339 boasts robust construction and a reliable pump design. The 44339 model is designed for larger projects, offering a higher pressure output, which translates to faster coverage and reduced working time. Its ergonomic handle and lightweight design ensure easy maneuverability, helping users to paint larger areas with less fatigue.

Both models incorporate Graco's Recognized Technology, including the SmartControl system. This technology provides users with precise pressure control, allowing for optimal spray patterns and consistent results. This feature is especially beneficial when working on intricate projects requiring attention to detail, such as fences or cabinetry.

Another notable characteristic of these sprayers is the RAC X tip system, which offers a wide range of spray tips for various applications. This flexibility enables users to switch between different nozzle sizes quickly, accommodating everything from broad surfaces to finer finishes. Coupled with an easy-to-clean design, this makes both models user-friendly and efficient.

Additionally, the Graco 44164 and 44339 come equipped with an integrated filter to protect the pump from debris and clogs, ensuring uninterrupted performance. Their robust build quality and reliable components mean users can expect longevity from these sprayers, reducing the necessity for maintenance and repairs.

In summary, the Graco 44164 and 44339 are exceptional airless paint sprayers designed to meet the needs of both professionals and DIY users. With their powerful performance, advanced technologies, and user-friendly features, these models are ideal for completing a variety of painting projects efficiently and effectively. Whether you are tackling indoor spaces, outdoor surfaces, or intricate detailing, Graco's reliable build and innovative design can help transform your painting experience.
Top Page Image Contents