Dantax LR-7500 manual Surround back speakers, Subwoofer

Page 7

Connections

Surround back speakers

Surround back speakers are required when a full 7.1-chan- nel system is installed.

Speakers should be placed on a rear wall, behind the lis- tening position.

The center of the speaker should face into the room.

Subwoofer

We recommend using a subwoofer to have maximum bass effect. Subwoofer bears only low frequency range so you can place it any where in the room.

HEIGHT OF THE SPEAKER UNITS

Front left and right speakers, and a center speaker

Align the tweeters and mid-range drivers on the three front speakers at the same height, as best as possible.

Surround left and right speakers, and surround back speaker

Place the surround left, right and surround back speakers higher than your ears by about 70cm -1m.

Also place the speakers at the same height, as best as pos- sible.

70cm

1m

Note:

•Use magnetically-shielded speakers for front left, right and the center speakers when the speakers are installed near the TV and the TV is a monitor type.

CONNECTING SPEAKER WIRE

1.Strip away approx. 10 mm of wire insulation.

2.Twist the bared wire ends tight, to prevent short circuits.

3.Loosen the knob by turning it counterclockwise.

4.Insert the bare part of the wire into the hole in side of each terminal.

5.Tighten the knob by turning it clockwise to secure the wire.

1.2.

10mm

3.4. 5.

Caution:

•Be sure to use speakers with the specified impedance as shown on the rear panel of this unit.

•To prevent damage to circuitry, do not let the bare speak- er wires touch each other and do not let them touch any metal part of this unit.

•Do not touch the speaker terminals when the power is on. It may cause you to receive an electric shocks.

•Do not connect more than one speaker cable to one speaker terminal. Doing so may damage this unit.

Note:

•Be sure to connect the positive and negative cables for the speaker properly. If they are miss connected, the sig- nal phase will be reversed and the signal quality will be corrupted.

CONNECTING A SUBWOOFER

Use the PRE OUT SUBWOOFER jack to connect a powered subwoofer (power amplifier built in ).

If your subwoofer is a passive type (power amplifier is not built in), connect a monaural power amplifier to the PRE OUT SUBWOOFER jack and connect the subwoofer to the amplifier.

- 7 -

Page 6 Page 8
Image 7
Page 6 Page 8
Contents LR-7500 If in Doubt Consult a Competent ELECTRI- Cian Important Safety InstructionsIMPORTANTfor U.K.Customers Blue Neutral Brown LiveTable of Contents Back-up Memory Function When to Use ResetBefore Use Read this before operationNeo6 offers several important improvements as follow DescriptionCenter speaker Description ConnectionsAbout Dolby Pro Logic Front left and right speakersSurround left and right speakers, and surround back speaker Surround back speakersSubwoofer Front left and right speakers, and a center speakerPRE OUT SUB Woofer jack Power cord AC InputRS-232C Audio Components Component jack Video jackVideo convert Video Components and Advanced Connecting Connecting the supplied AM loop antenna Connecting the supplied FM antennaFront Panel Control FunctionsTV / VID Display Remote Control UnitPower TEST-TDirection Tuning UP/DOWNPreset UP/ Down TOP MenuControl Functions Basic Operations Tone Control Volume knobSurround Mode Selector Sleep Timer FunctionOFF Surround Mode Night ModeMAX MIDSize of Speakers Speaker ConfigurationInput the distance from your listening position Balancing relative volume between speakers using Test ToneTuner-Mode Preset MemoryTuner Operation Station SelectionCT Clock Time RDS Radio Data System Remote Controller OnlyPS Program Service Name PTY Program TypeVideo Tape Dubbing System Configuration OSD On Screen DisplayMaking Configuration Adjustments Video OperationsFunction Setup System ConfigurationFunction Setup Surround SetupDolby Surround Dolby SurrUpsampling Speaker Setup CH Level Adjust Distance AdjustPreference Setup Code Check Method Controlling other Components Connected to the LR-7500Direct Code Entry Method Manual Search MethodVCR Brand List Programming the RemoteSAT Brand List TV Brand List Erres Pathe Cinema Symptom Cause Solution TroubleshootingPAL / Ntsc SpecificationsOutput Power DTSLuxman CORPORATION, Japan

LR-7500 specifications

The Dantax LR-7500 is an advanced audio receiver that embodies the perfect blend of cutting-edge technology, sleek design, and versatile functionality. Tailored for audiophiles and general users alike, the LR-7500 boasts a variety of features that set it apart in the realm of home audio systems.

One of the standout features of the Dantax LR-7500 is its extensive connectivity options. The receiver supports various input sources, including HDMI, optical, USB, and traditional analog connections, ensuring compatibility with a wide range of devices such as televisions, gaming consoles, and streaming players. The inclusion of Bluetooth functionality allows users to stream music wirelessly from their smartphones and tablets, providing convenient access to digital audio libraries and online streaming services.

In terms of sound quality, the LR-7500 is equipped with high-quality digital-to-analog converters (DACs) that deliver crystal-clear audio reproduction across the frequency spectrum. The receiver supports high-resolution audio formats, making it an excellent choice for those who appreciate the nuances of music. With built-in equalization settings, users can customize their listening experience, optimizing sound performance to suit their preferences.

The Dantax LR-7500 also features advanced surround sound technologies, such as Dolby Atmos and DTS:X, which create an immersive audio experience for home theater enthusiasts. These technologies envelop listeners in three-dimensional soundscapes that enhance movies, music, and gaming.

Another significant characteristic of the LR-7500 is its user-friendly interface. The receiver comes with an intuitive remote control and a well-designed on-screen menu, making navigation seamless and straightforward. Additionally, the device offers support for multi-room audio, allowing users to enjoy synchronized sound in different areas of their home.

Durability and aesthetics are also key considerations in the design of the Dantax LR-7500. The unit features a robust build, ensuring reliability over time, while its modern and stylish appearance allows it to complement any home décor.

In summary, the Dantax LR-7500 is a state-of-the-art audio receiver that combines high-quality sound reproduction, extensive connectivity options, and user-friendly features. Whether for music, movies, or gaming, it stands out as a versatile solution, making it an excellent choice for any audio enthusiast looking to enhance their listening experience.
Top Page Image Contents