Atlas 330 instruction manual Expanding Your System, Error Messages, System Settings, What To Do

Page 9

Error Messages:

Display

Error Description

 

 

A short circuit has been detected on the programming track.

E

 

 

Check relevant connections and/or decoder installation in the

 

locomotive.

 

 

No value was found during the readout of a Register, or no

E

2

response was received after a value was entered. However, this

does not necessarily mean the decoder did not accept the new

values. Please try using the new address before attempting to program again. You should also check if the locomotive is on the right programming track and/or the installation of the decoder.

System Settings

The following system parameters can be edited or viewed:

Version number of the Commander software (view only).

Service number of the Commander. You will be asked to identify this number if you call in for assistance with your Commander.

If your Commander is set to function as a master or as a slave (also called an XpressNET unit).

1. Press both

 

 

and

 

buttons at the same time to access the Menu system.

 

 

 

 

 

 

Use the "+"

or "-" buttons to scroll to the System menu.

 

 

Display

 

What To Do

 

 

SY.S

 

Press Enter to select the System mode setting.

 

 

 

 

 

.

 

 

 

The first system setting (shown to left) is the Commander

 

 

 

 

 

 

 

 

 

 

 

Y

 

software version number setting option.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press Enter to view the version number. You cannot

 

.

 

change this value; it is read-only. Press Exit to go back to

 

 

System menu.

 

 

 

Y

2

 

Press +/- buttons until you see the service number system

 

setting option (shown on left).

 

 

 

Press Enter to view the service number. You cannot

 

02

 

 

 

change this value; it is read-only. Press Exit to go back to the

 

 

System menu.

 

.

 

Press "+" or "-" button until you see the Master/Slave system

 

 

Y 9 0

 

setting (shown on left). Press Enter to select setting options.

 

 

 

Press "+" or "-" button to scroll through the options. To make

 

 

 

 

 

 

your Commander operate in master mode, press Enter when

 

 

 

you see the display on left.

To have your Commander operate in slave mode, press Enter when you see display on left. Press Exit to leave the menu.

EXPANDING YOUR SYSTEM

Adding Additional Throttles

If you would like to have more than one operator on your layout, you may connect up to five additional Commanders or handhelds that conform to XpressNET standards to your original unit. When you have more than one Commander, one becomes the "master" and the other(s) become "slaves." The master provides track power, the slaves do not. Any Commander (master or slave) that is connected to a Generator may be used for programming. In the case of a slave that is used for programming, it must be connected to a pro- gramming track via output terminals P & Q and must be connected to a

15

16

Image 9
Contents Item #330 Adding More Power to Your LayoutTable of Contents Getting Started Setting Up Your Layout to Run DCCMini flathead screwdriver Decoder PreparationRunning Your Locomotive Using the Atlas Master DCC CommanderActive Function Display Recalling LocomotivesActivating Functions Emergency StopAccessing the Menu When acquiring a locomotive that is currently runningMenu Menu SelectionsSetting Speed Steps Speed Step AssignmentProgramming Your Decoder STEP-BY-STEP Decoder Programming Programming a Locomotive’s Decoder AddressDisplay What To Do System Settings Error MessagesExpanding Your System What To DoConnect the master Commander to the Generator Connecting Two Commanders Using One GeneratorSlave Commander cannot be used to power the track Er99 No XpressNET-connection