Yamaha RX-V363 owner manual Connecting the FM and AM antennas, Connecting the power cable, 19 En

Page 23

01EN_RX-V363_U.book Page 19 Friday, December 7, 2007 5:44 PM

Connecting the FM and AM antennas

Both FM and AM indoor antennas are supplied with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals.

Notes

•The AM loop antenna should be placed away from this unit.

•A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center about outdoor antennas.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

Outdoor AM antenna

 

 

 

AM loop

Use a 5 to 10 m (16 to 32

 

 

 

antenna

ft) of vinyl-covered wire

 

 

 

(supplied)

extended outdoors from a

 

 

 

 

window.

 

 

 

 

Connections

Assembling the supplied AM loop antenna

Note

The types of the supplied AM loop antenna is different depending on the models.

Connecting the power cable

Once all connections are complete, plug the power cable into the AC wall outlet.

PREPARATION

DEO

N DVR OUT

MONITOR

 

 

OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

DVR

 

AUDIO

CD

N

OUT

 

 

ANTENNA

AM

GND

FM

75

UNBAL.

IN

MD/

(PLAY) CD-R

RSURRO

OUTP

OUT (REC)

Indoor FM antenna (supplied)

Power cable

(U.S.A. model)

To the AC wall outlet

Ground

For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

Connecting the wire of the AM loop antenna

Open the

Insert

Close the

lever

 

lever

y

The wire of the AM loop antenna does not have any polarity and you can connect either end of the wire to AM or GND terminal.

Turning on and off the power

■Turning on this unit

Press A STANDBY/ON (or DPOWER) to turn on this unit.

y

When you turn on this unit, there will be a 4 to 5-second delay before this unit can reproduce sound.

■Set this unit to the standby mode

Press A STANDBY/ON (or ESTANDBY) to set this unit to the standby mode.

Note

In the standby mode, this unit consumes a small amount of power in order to receive infrared signals from the remote control.

English

19 En

Black process 45.0° 240.0 LPI

Page 22 Page 24
Image 23
Page 22 Page 24
Contents
RX-V363 Product and cart combination should be moved Important Safety InstructionsExample of Antenna Grounding FCC Information for US customersSerial No For Canadian CustomersPour LES Consommateurs Canadiens Contents We Want You Listening For a Lifetime FeaturesAsia and General models only Checking the supplied accessoriesInstalling batteries in the remote control Getting startedEnjoy DVD playback Set up your speakersQuick start guide Preparation Check the itemsConnect the subwoofer cable to the input Front speakersCenter and surround speakers Player are unplugged from the AC wall outlets For further connectionsMake sure that this unit and the DVD Check the type of the connected speakers Using the other Scene buttonsRotate H Volume to adjust the volume About Scene functionWhat do you want to do with this unit? Name See ConnectionsRear panel 10 En Placing speakers11 En Connecting speakersBefore connecting to the Speakers Terminal 12 En Connecting to the Front a terminalsConnecting to the Front B, CENTER, and Surround terminals Video jacks Information on jacks and cable plugs13 En Audio jacksHdmi cable plug Information on Hdmi14 En Hdmi jack and cable plug Digital or analog audio input jacks of this unit Connecting video components 15 En Audio outHdmi connection Connecting to the Hdmi or Component Video jacksConnecting to the Component Video jacks 16 En17 En Connecting audio componentsConnecting a CD player and a CD recorder/MD recorder Connecting to the Multi CH Input jacks18 En Connecting to the Video AUX jacks on the front panel19 En Connecting the FM and AM antennasConnecting the power cable Turning on and off the power20 En Front panel display30º Using the remote control21 En 1Infrared window22 En Basic setupSPEAKERS..5spk 23 En Press 7l/ h to select the desired settingPress Hmenu to exit from Basic Setup CHECKTestToneD V i e w i n g Selecting the Scene templatesSelecting the desired Scene template D M o v i e V i e wWhich Scene template would you like to select? 25 En26 En Preset Scene template descriptionsRenaming the Scene templates Customizing the preset Scene TemplatesCreating your original Scene templates 27 EnScene buttons Using remote control on the Scene featureControlling the input source Components in the Scene mode 28 EnV i e D r a m a t i c Guide to contentsPlayback Basic operations30 En Additional operationsSelecting audio input jacks Selecting the night listening modeAdjusting the tonal quality 31 En32 En Adjusting speaker levels during PlaybackDisplaying the signal information Press 4AMP and then press Hmenu on the remote controlAudio sources Using the sleep timer33 En Playing video sources Background34 En Category Program FeaturesSound field programs Sound field program descriptionsEditing sound fields parameters 35 EnTo deactivate the Straight mode, press Enjoying unprocessed input sources Straight decoding mode36 En AM 1440 kHz FM/AM tuningAutomatic tuning Manual tuning38 En Automatic preset tuningManual preset tuning C3AM 630 kHzE1FM 87.5 MHz Selecting preset stationsExchanging preset stations Press and hold B PRESET/TUNING for more than 3 secondsAUX/DOCK Using iPod40 En Select V-AUX as the input source Using Bluetooth componentsPairing by using SET Menu Quick pairing42 En RecordingSet menu Basic setup Basic SetupManual setup Manual Setup Parameter Features8RETURN Using set menuSignal information Signal Info 44 En45 En Speaker settings Aspeaker SETSpeaker level BSP Level 46 En47 En 100HzInput assignment Audio settings Gaudio SET48 En BGV BGV Multi channel input setupDVD My DVD 49 EnParameter initialization DPARAM. INI Display settings Adisplay SETBluetooth setting Ebluetooth 50 EnControlling this unit Remote control featuresControlling this unit, a TV, or other components 51 EnDigital TV Remote control Player/recor52 En Controlling other components53 En Setting remote control codesResetting all remote control codes Remote control code default settingsSpeaker impedance SP IMP A. and Canada models only Advanced setupInitializing Preset 54 EnGeneral TroubleshootingProblem Cause Remedy See 55 En56 En Tuner 57 EnStatus message Cause Remedy See Bluetooth58 En IPod59 En Remote controlResetting the system Advanced setup menu appears in the front panel displayAudio information Glossary60 En Cinema DSP 61 EnSound field program information Video information62 En SpecificationsNumerics Index63 En 64 En Page C D E F G H Front panel10 ENT Iii List of remote control codesCCE NEI VCR TV/DVDTV/DVD/VCR TV/VCRWN25860
Related manuals
Manual 77 pages 4.4 Kb
Top Page Image Contents