Yamaha CRW-F1-NB manual Set the Jumper Switch

Page 24

Preparing the CRW-F1 Drive

2 Set the Jumper Switch

Refer to the examples of connecting the CRW-F1 drive on page 12, and set the CRW-F1 drive to master/slave to support your computer environment.

Set the plastic shunt at the jumper switch on the rear panel with narrow pliers.

The position to be inserted the plastic shunt varies depending on the setting.

 

 

 

 

Master

 

 

 

 

 

Slave

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(default)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The CRW-F1 drive is set at slave by default.

When replacing an IDE device (master) with the CRW-F1 drive, set the drive to master.

15

Page 23 Page 25
Image 24
Page 23 Page 25
Contents
Page FCC Information U.S.A Achtung Page English Safety Precautions Iii Warranty Precautions for TransportationTable of Contents Features of the CRW-F1 Drive DiscT@2High speed writing/reading SafeBurn Enhanced stability writing technologyNames and Functions of Parts Front PanelRear Panel Names and Functions of PartsPrecautions on Use Handling DiscsCopyright Disclaimer of IndemnityCompatible Discs Disc shapeRecordable disc type CD-RW discs Writing/Rewriting speedHigh Speed CD-RW discs Ultra Speed CD-RW discs System Requirements Computer PC/AT compatibleImage file Operating systemPreparing the CRW-F1 Drive Serial NumberPreparing tools Serial NumberDecide the Installation Method Turn off and unplug the computerReplacing an existing IDE device with the CRW-F1 drive Examples of connecting the CRW-F1 drive Example 1 As a secondary slave For additional drivePreparing the CRW-F1 Drive Enhanced-IDE E-IDEPage Set the Jumper Switch Cable Select Csel Install the CRW-F1 Drive Installing the CRW-F1 drive as an additional driveReplacing Connect a 40-pin IDE cable Connect an audio cable if necessary Audio CD playbackAnalog connection Digital connection Top Power connector Bottom Check Recognition of the CRW-F1 Drive For Windows XPIf the drive name is not shown or there is or mark For Windows 2000 ProfessionalFor Windows 95/98/98 Second Edition/Me For Windows XP/2000 Professional Install CD Writing Software Recommended DMA settings transfer mode settingsDirect Memory Access DMA Loading/Ejecting a Disc Manually Ejecting a Disc Troubleshooting CRW-F1 drive is not recognized by the operating system. PIs the IDE cable connected properly to the CRW-F1 drive? Is the IDE cable connected properly to the motherboard?Disc tray does not open when you press the eject button Is the disc tray opened when the computer is restarted?Is each IDE device set respectively? Is the CRW-F1 drive recognized by the operating system? PNo data can be read from a disc Check that the volume is not set to the minimum level Playback of an audio CD CD-DA is inaudibleFor Windows Me Error message Buffer Underrun is displayed Other problemsIs the power capacity of your computer sufficient? Firmware Checking the firmware version in your CRW-F1 driveCRW-F1 Drive Specifications Supported Formats Write Read Play back *4Data Transfer Rate Mode CRW-F1 Drive Specifications Safety/EMC Compliance CRW-F1 drive conforms to the following specificationsTechnical Notes Buffer Underrun Protection FunctionWriting Methods Disc-at-Once DAOTechnical Notes Session-at-Once SAO Packet WritingConstant Linear Velocity CLV Constant Angular Velocity CAVPartial CAV Page Canada