Hitachi KP-DE500, KP-E500 Setting WB detection area, ONNO.* *1 ～9, ･AWC preset white balance

Setting WB detection area

1)Use the UP and DOWN buttons to shift the cursor to “WB AREA”.

2)Press the SET button to shift the mode in the sequence

“OFF”, “ON(NO.*)”. [*1～9]	Factory setting is “OFF”.
OFF	: All the screens
ON(NO.*) [*1～9]	: Only the selection area

3)When the display is turned “ON(NO.*), “AREA SELECT” is displayed in the line in the under.

4)Shift the cursor to “AREA SELECT” and push the SET button to display the detection area(WB) select menu.

6)There are 9 white detect areas selected by the UP and DOWN buttons. Select the areas from nos. 1 to 9 that include the subject of main interest. (Factory setting is NO.1)

UP button	: 1→2→3→4→5→6→7→8→9
	(ascending order)
DOWN button	: 9→8→7→6→5→4→3→2→1
	(descending order)

6)After deciding the detection area, push the SET button to return to the “WHITE BALANE MENU”.

ＡＲＥＡ（ＷＢ）

ＮＯ．１

┏━━━━━━┓

┃ ┃

┃ ┃

┗━━━━━━┛

Detect area position

6 5 4

2 1 3

7 8 9

DETECTTION AREA (WB) SELECT MENU

27

･AWC (preset white balance)

After white balance condition is set, it is automatically stored in memory. The AWC mode should be used where the color temperature does not change once it has been set. The color temperature adjustment range of AWC is 2300 K～10,000 K.

◆ ＷＨＩＴＥ	ＢＡＬＡＮＣＥ ＭＥＮＵ ◆
>ＭＯＤＥ	：ＡＷＣ		…… Select White Balance mode
ＰＲＥＳＥＴ	ＳＴＡＲＴ ：ＰＵＳＨ ＳＥＴ		…… Set preset start
Ｒ－ＧＡＩＮ	ＯＦＦＳＥＴ：	０００	…… Adjustment of the R gain offset
Ｂ－ＧＡＩＮ	ＯＦＦＳＥＴ：	０００	…… Adjustment of the B gain offset
ＲＥＴ			…… Return to the main menu
			…… End of menu display
ＥＮＤ

WHITE BALANCE MENU (MODE: AWC)

1)Use the UP and DOWN buttons to shift the cursor to “PRESET START”.

2)Select a white object to image near the center of the screen.

3)When a SET button switch is pushed, the white balance adjustment is begun. At that time, “PUSH SET” enters the state of blinking.

4)The cursor moves to “R-GAIN OFFSET” when the automatic setting is completed. The time required in the automatic setting changes depending on the light condition. If the white balance is not correct after about 15 seconds, please repeat the process from step 1.

Fine-tuning of white balance

After Preset is completed, the white balance can be fine-tuned by the R/B gain offset.

1)Use the UP and DOWN buttons to shift the cursor to “R-GAIN OFFSET” or “B-GAIN OFFSET”, then press the SET button. The adjustment value at the right of value flashes.

2)Change the “R-GAIN OFFSET” or “B-GAIN OFFSET” by pressing the UP and DOWN buttons.

(Variable range: -128～000～+127)

3)Return the factory setting(000) by simultaneously pressing the UP and DOWN buttons for two seconds.

4)The setting is fixed when the SET button is pushed, and the cursor moves below by one line.

28