Hitachi KP-E500, KP-DE500 operation manual Sub Menu

Sub Menu

The sub menu is used for changing the picture quality (video response) of the camera output image.

1) Press the SET button for longer than 2 seconds to display the “MAIN MENU”.

2) Use the UP and DOWN buttons to shift the cursor to “SUB MENU”, then press the SET button to display the “SUB MENU”.

◆ ＳＵＢ	ＭＥＮＵ ◆
>ＩＴＥＭ	：ＰＩＣＴＵＲＥ		…… Select SUB MENU item
ＣＨＲＯＭＡ	：	０００	…… Chroma setting[*]
ＤＥＴＡＩＬ	：	０００	…… Detail setting
ＰＥＤＥＳＴＡＬ	：	０００	…… Pedestal level setting
ＧＡＭＭＡ	：ＯＮ		…… Gamma setting
ＤＮＲ	：ＡＵＴＯ（ＨＩＧＨ）		…… Digital noise reduction setting
ＰＯＬＡＲＩＴＹ	：ＰＯＳＩＴＩＶＥ		…… Negative/positive
ＲＥＴ			…… Return to the main menu
ＥＮＤ			…… End of menu display
				(*) Note: KP-E500 is not displayed.

SUB MENU (ITEM: PICTURE)

･CHROMA [Only KP-DE500 Type]

The optimum color level has been set at the factory. If necessary, this can be changed as follows.

1)Use the UP and DOWN buttons to shift the cursor to “CHROMA”, then press the SET button. The adjustment value at the right of value flashes.

2)Change the “CHROMA” by pressing the UP and DOWN buttons. (Variable range: -128～000～+50)

3)Return the factory setting(000) by simultaneously pressing the UP and DOWN buttons for two seconds.

4)The setting is fixed when the SET button is pushed, and the cursor moves below by one line.

NOTE

1)The color noise might stand out when the color level is raised.

2)CHROMA is fixed to “-128” and cannot be adjusted by the B/W MODE setting at a monochrome image.

･DETAIL

The optimum detail level has been set at the factory. If necessary, this can be changed as follows.

1)Use the UP and DOWN buttons to shift the cursor to “DETAIL”, then press the SET button. The adjustment value at the right of value flashes.

2)Change the “DETAIL” by pressing the UP and DOWN buttons. (Variable range: -128～000～+127)

3)Return the factory setting(000) by simultaneously pressing the UP and DOWN buttons for two seconds.

4)The setting is fixed when the SET button is pushed, and the cursor moves below by one line.

29

NOTE

The noise might stand out when the detail level is raised.

･PEDESTAL

The optimum pedestal level has been set at the factory. If necessary, this can be changed as follows.

1)Use the UP and DOWN buttons to shift the cursor to “PEDESTAL”, then press the SET button. The adjustment value at the right of value flashes.

2)Change the “PEDESTAL” by pressing the UP and DOWN buttons. (Variable range: -128～000～+127)

3)Return the factory setting(000) by simultaneously pressing the UP and DOWN buttons for two seconds.

4)The setting is fixed when the SET button is pushed, and the cursor moves below by one line.

･GAMMA

1)Use the UP and DOWN buttons to shift the cursor to “GAMMA”.

2)Press the SET button to shift the mode in the sequence “ON”, “OFF”. Factory setting is “ON”.

OFF : γ=1.0

ON : γ=0.45

30

･DNR (Digital noise reduction)

It is a function to decrease the noise generation by AGC.

1)Use the UP and DOWN buttons to shift the cursor to “DNR”.

2)Press the SET button to select the setting sequentially in the following order. Factory setting is “AUTO(HIGH)”.

SET button: AUTO(HIGH)→ON-1→ON-2→ON-3→ON-4 →ON-5→ON-6→ON-7→OFF →AUTO(LOW)→AUTO(MID)

AUTO( )	: It synchronizes with the amplification of
	AGC and the DNR setting changes from
	turning “OFF” to “ON-7”.
LOW	: Movement priority mode
	(Change into “ON-5” in the maximum. )
MID	: The middle mode
	(Change into “ON-6” in the maximum. )
HIGH	: Image quality priority mode
	(Change into “ON-7” in the maximum. )
OFF	: DNR doesn't operate.
ON-*(1～7)	: DNR always operates. The afterimage
	increases according to the coefficient of
	the mode, and the noise decrease is
	effective.