Hitachi KP-E500, KP-DE500 Menu operations, Main Menu, Camera Title Menu, Display character input

Menu operations

Three rear panel setup buttons are used to shift the cursor and select items from the menus.

Main Menu

1)Press the SET button for at least 2 seconds to display the main menu on the monitor screen.

	①
	②
	③
① Up button	: Shift the cursor in the upward direction or
	increase an adjustment value.

◆◆ ＭＡＩＮ ＭＥＮＵ ◆◆

>ＣＡＭＥＲＡ		ＴＩＴＬＥ	：ＯＦＦ ↵
ＬＩＧＨＴ ＣＯＮＴＲＯＬ：ＯＦＦ				↵
ＡＧＣ			：ＯＮ	↵
ＳＨＵＴＴＥＲ		ＳＰＥＥＤ：ＯＦＦ
ＳＥＮＳ	ＵＰ		：ＯＦＦ
Ｂ／Ｗ	ＭＯＤＥ		：ＯＦＦ

ＷＨＩＴＥ ＢＡＬＡＮＣＥ：ＡＴＷ ↵ ＳＵＢ ＭＥＮＵ ↵

ＥＮＤ

MAIN MENU

……Camera title setting menu

……Light control setting menu

……AGC setting menu

……Shutter speed setting

……Sensitivity enhance Setting

……B/W mode setting (*)

……White balance mode setting menu (*)

……Sub menu

……End of menu display

(*)Note: KP-E500 is not displayed.

②	Down button	: Shift the cursor in the downward direction
		or decrease an adjustment value.
③	Set button	: Press to display the main menu or to
		change a setting.

Note:

lf no button is pressed, the menu display extinguishes automatically after about 5 minutes.

2)Check the present settings at the main menu.

3)Shift the cursor vertically by pressing the UP and DOWN buttons, then press the SET button to enable changing the setting of the selected item.

4)If changes are unnecessary, shift the cursor to “END” and Press the SET button to return to the normal screen.

5)When an item indicated by a ↵ mark is selected, pressing the SET button shifts to the next menu.

13

Camera Title Menu

One line of up to 22 alphanumeric characters can be displayed on the screen. The display on/off and position are selected at the

Display character input

1)When the mode is Top or Bottom, the characters indicated in the figure can be used.

camera title menu.

1)	Press the SET button for longer than 2 seconds to display
	the main menu.
2)	Use the UP and DOWN buttons to shift the cursor to
	“CAMERA TITLE”, then press the SET button to display the
	camera title menu.
3)	While the cursor is at “MODE”, press the SET button to shift

◆ ＣＡＭＥＲＡ ＴＩＴＬＥ ＭＥＮＵ ◆

>ＭＯＤＥ：ＴＯＰ ０１２３４５６７８９

ＡＢＣＤＥＦＧＨＩＪＫＬＭ ＮＯＰＱＲＳＴＵＶＷＸＹＺ ！？＃＆（ ）、 ．：；～＊％ ＋－ｘ／＝“‘

ＳＰＡＣＥ		←	→ ＲＥＳＥＴ
ＰＯＳＩＴＩＯＮ		ＲＥＴ	ＥＮＤ
ＣＡＭＥＲＡ	ＮＯ．１・・・・・・・・・・・

……Display On/OFF and position ( OFF / TOP / BOTTOM )

Input character select table

……Blank, cursor shift (left / right), character delete

……Display position, return, end

……Input character display

the mode in the sequence “OFF”, “TOP”, “BOTTOM”.

OFF		: Characters not displayed. (Factory setting)
TOP		: Characters displayed at top of screen.
BOTTOM		: Characters displayed at bottom of screen.
◆ ＣＡＭＥＲＡ ＴＩＴＬＥ ＭＥＮＵ ◆
>ＭＯＤＥ	：ＯＦＦ		…… Display On/OFF and position
			( OFF / TOP / BOTTOM )

ＲＥＴ	…… Return to the main menu
ＥＮＤ	…… End of menu display

CAMERA TITLE MENU (MODE: TOP or BOTTOM)

2)Press the DOWN button, then use the UP and DOWN buttons to shift the flashing cursor sequentially among the usable characters.

3)When the SET button is pressed, the selected character is entered in sequence beginning with the left-most of 22 dots shown at the bottom of the screen.

Afterwards, each newly selected character is entered sequentially toward the right.

The item under character input selecting department uses it in the following manner.

SPACE : To add a blank space, shift the flashing cursor to “SPACE”, then press the SET button.

CAMERA TITLE MENU (MODE: OFF)

14