Video Coax Connection, Final Assembly | Sanyo VSE-2300, VSE-2400

Be sure to securely tighten all fittings to ensure a liquid-tight seal. Failure to do so could allow water to enter the housing and damage the camera and lens.

6.Connect the supply power wires to the left side or the top side of the terminal block provided. Strip no less than 6 mm (0.25-inch) and no more than 8 mm (0.31-inch) of insulation away from the wire. Be sure not to nick the wires.

7.Cut the camera power cord, leaving enough cable to allow connection to the terminal block. Strip no less than 6 mm (0.25-inch) and no more than 8 mm (0.31-inch) of insulation away from the wire. Be sure not to nick the wires. Connect these wires to the left side or the top side of the terminal block.

8.On heater and heater/blower units, make sure the heater and fan wires stay connected to the terminal block.

6.7Video Coax Connection

WARNING: Only use the cables specified under "INSTALLATION, Cable Requirements" for wiring of the video coax connection.

1.For VSE-2300 versions, install a 1/2-inch NPT fitting into the remaining hole in the rear cap. For VSE-2400 versions, install a 3/8-inch NPT fitting through the center small hole of the rear cap.

2.Route the video coax cable through one of the fittings installed in step 1 or one of the feed-through fittings in the base.

3.Attach BNC connector to the coax and connect it to the

camera. Pull any excess wire out of the housing and tighten the fitting to 8.5 N.m to 9.0 N.m (75 in.lb to 80 in.lb). This torque rating is approximately 1 to 1-1/2 turns

past the point where the fitting starts to grip the wire. Failure to do so will result in water damage to all electronic parts.

Be sure to securely tighten all fittings to ensure a liquid-tight seal. Failure to do so could allow water to enter the housing and damage the camera and lens.

Use of "drip loops" is recommended on the wiring outside of the rear end cap.

6.8Lens Wiring

WARNING: Only use the cables specified under "INSTALLATION, Cable Requirements" for wiring of the lens.

1.Install the last 1/2-inch NPT fitting into the remaining hole in the rear cap. Zoom lenses can only be installed into VSE-2400 housings.

2.If installing a zoom lens, insert the lens control cable through the last fitting at the rear of the housing. Attach the lens wiring to the lens mating connector and connect it to the lens. If mating connector is not available, connect

directly to the lens cable. Pull any excess wire out of the housing and tighten the fitting to 8.5 N.m to 9.0 N.m

(75 in.lb to 80 in.lb). This torque rating is approximately 1 to 1-1/2 turns past the point where the fitting starts to grip the wire. Failure to do so will result in water damage to all electronic parts.

NOTE: See specification on lens cord for correct plug connection.

Be sure to securely tighten all fittings to ensure a liquid-tight seal. Failure to do so could allow water to enter the housing and damage the camera and lens.

3.If using a pan/tilt with a feed-through cable, insert the camera/lens function cable in through the left fitting at the rear of the cradle. Wire the functions as described above or as needed.

Use of "drip loops" is recommended on the wiring outside of the rear end cap.

6.9Camera/Lens Adjustment

Verify camera and lens operation before final assembly of the cradle into the housing. Adjust the camera focus and iris as necessary. See individual camera instructions.

6.10 Final Assembly

1.Use the plugs or fittings provided to plug any remaining holes in the rear cap.

2.Reinstall the cover. Align the bottom of the cover ribs with the top of the base. Slide the cover onto the base. Make sure the seal is not folded over or torn. Use silicone grease to lubricate the seals if necessary. See Figure 10.

VSE-2300, VSE-2400 specifications

The Sanyo VSE-2400 and VSE-2300 are modern audio-visual systems known for their exceptional performance and versatility, appealing to both casual listeners and audiophiles alike. These systems integrate advanced technology to enhance sound quality, making them a popular choice for home entertainment.

The VSE-2400 boasts an impressive array of features designed to deliver immersive sound experiences. It is equipped with a powerful digital amplifier that ensures high-fidelity audio reproduction. The unit supports a variety of audio formats and can play CDs, MP3s, and streaming services, making it a versatile option for any music lover. Its sleek design is complemented by a user-friendly interface, allowing users to navigate through their media libraries with ease.

One of the main technologies that sets the Sanyo VSE-2400 apart is its implementation of digital signal processing (DSP). This technology optimizes sound output by automatically adjusting audio settings based on the type of content being played. Whether it's a movie, music, or a podcast, the DSP ensures that users receive the best audio quality tailored to their listening preferences.

The VSE-2300, on the other hand, is slightly more compact yet does not compromise on sound quality. This system is ideal for those with limited space but still want a robust audio solution. Like the VSE-2400, it features a high-efficiency digital amplifier, ensuring clean and powerful sound output without distortion.

Both models include Bluetooth connectivity, allowing users to connect their smartphones or tablets wirelessly for seamless music streaming. Additionally, they come equipped with USB ports and auxiliary inputs, offering flexibility in how users choose to play their audio content.

A common characteristic of the VSE series is their built-in equalizers, enabling users to customize audio settings to better suit their preferences. The systems also include remote control functionality, enhancing convenience for users who wish to operate their audio systems from a distance.

In conclusion, the Sanyo VSE-2400 and VSE-2300 are excellent audio-visual systems that offer a rich set of features and technologies, catering to a diverse range of listening needs. Whether for casual enjoyment or serious listening, these systems provide quality sound and easy connectivity, making them worthy additions to any home entertainment setup.