TRIPOD SET-UP
1.Before
2.Remove tripod from the Softcase and unclip the Transport Clips.
3.Place the Tripod Feet on level surface (if possible) and release the Sprint Lok Upper Lever on each leg.
4.Lift the top of the tripod to a desired height and then apply the Sprint Lok Upper Lever on each leg.
5.Release the Sprint Lok Lower Lever on each leg, then lift the tripod to a desired height and then apply the Sprint Lok Lower Lever on each leg.
6.Spread the Tripod Legs apart, check that the Tripod Bowl is approxi- mately level to the ground.
7.Check that the tripod is secure.
TRANSPORT CLIPS
The 2 Transport Clips (Fig 3), are | Transport Clip | Fig 3. |
designed to hold the Sprinter tripod’s |
|
|
three legs together during transport. |
|
|
Their |
|
|
are easily gripped and detached for |
|
|
set up, and reattached. The Transport |
|
|
Clips must be securely attached before |
|
|
transporting the tripod. |
|
|
CARRY HANDLE
The Sprinter II Inline patented Carry handle (fig 4.) is designed so the Sprinter II tripod and fluid head remain balanced while being carried by hand. The rubber handle offers secure grip,
LEG LOCK ADJUSTMENT
Over time the leg locks may need adjusting to prevent leg slippage.
Upper Leg Lock: ( Fig 7.)
For 1 & 2 stage Sprinter II Tripod.
Adjust the Upper Leg Lock Assembly in a locked position using (supplied) 5mm Hex Key - P6579.
1.Extend the upper stage half way and lock the Upper Lever.
2.Turn the Upper Leg lock adjuster clockwise 1/8th of a turn. Release Sprint Lok Upper Lever and ensure that stage slides freely.
3.When adjusted correctly Leg Lock Lever should only have a small amount of “free play” before locking action commences. If this free play is excessive repeat the steps above.
Lower Leg Lock: (Fig 8.)
For 2 stage Sprinter II Tripod only.
Adjust the Lower Leg Lock Assembly in locked position using a (supplied) 5mm Hex Key. - P6579
1.Extend the lower stage half way and lock the Lower Lever.
2.Tighten the lower leg lock adjuster screw gradually clockwise 1/8th of a turn. Release Lower Lever and ensure leg slides freely.
3.When adjusted correctly Leg Lock Lever should only have a small amount of “free play” before locking action commences. If this free play is excessive repeat the steps above.
When finished, ensure that all Leg Lock Levers lock flush with the tripod brackets.
TRIPOD PULL DOWN
1.Remove the camera from the Fluid Head.
2.Retract the spreader arms fully.
3.Hold and lift off the ground by two legs, then bring the legs inwards.
4.While holding the top of the tripod, release the Sprint Lok Upper Lever and Sprint Lok Lower Lever on each leg then lower completely.
5.Apply the Sprint Lok Upper Lever and Sprint Lok Lower Lever on each leg.
6.Attach both Transport Clips and return the tripod to the Softcase.
while the flexible nylon attachments let it rest, between the tripod legs, during shooting.
Fig 4.
5mm Hex key
5mm Hex key
Test each leg lock assembly by: | Fig 8. |
·Unlocking and locking lever several times.
·The lever should close with a definitive ‘click’.
·The end of the lever should close against the bracket.
·The tripod legs must slide freely when unlocked.
SPREADERS
Mid Level Spreader (Fig 5.)
The Mid Level Spreader allows the setting of the Tripods footprint and fine height adjustment. The tripod height and overall footprint can be adjusted by turning the Spreader Adjusting knob or by adjusting the length of the telescopic spreader arms.
MID LEVEL
SPREADER
Telescopic Clamp
Quick Release Latch | Fig 5. |
Spreader Set-up
1.Turn the Spreader Adjusting Knob
2.Stand the Tripod upright with legs spread out equally.
3.Release the Telescopic Clamp on the spreader arm then latch the Quick Release Latch on to the Self Aligning Swivel, repeat for the remaining two arms.
4.Bring each Tripod leg in such that the corresponding Spreader arm is fully retracted then lock the Telescopic Clamp, repeat for each Spreader arm.
5.Bring the Tripod legs towards the centre position, if resistance is felt do not force the Tripod legs, spread out the Tripod legs and make sure that the Spreader arms are fully retracted.
Spreader Pull Down
1.Remove the Camera and the Fluid Head from the Tripod.
2.Stand the Tripod upright with legs spread out equally and the Mid Level Spreader in the open position.
3.Pull back the Quick Release Latch knob and lift the Spreader arm from the Self Aligning Swivel, repeat for the remaining two arms.
Ground Spreader (Fig 6.)
The Miller Ground Spreader provides adjustment of each spreader arm to allow for lower height settings or uneven ground.
GROUND SPREADER
Adjustment Knob
Fig 6.
Spreader
1.Place the Ground Spreader on flat ground.
2.Place the socket of the Tripod Foot on to the ball of the Rubber Foot then pull the Rubber Stirrup up and over the Tripod Foot shoulder, repeat for the remaining two Tripod Feet.
Spreader Pull Down
1.Remove the Camera and the Fluid Head from the Tripod.
2.Pull the Rubber Stirrup up and outwards over the Tripod Foot shoulder, repeat for the remaining two Tripod Feet.
Fig 7.
LEG TO BOWL ADJUSTMENT
The leg to bowl pivot joint on the Sprinter tripod should have no lateral or free play movement and should swing with a firm, smooth resistance. Adjustment is usually not required; however, should it become necessary, the following procedure must be observed. (Fig 9.)
1.Leg to Bowl Adjustment to eliminate lateral or free play movement: Using a cross head screwdriver, ensure Bracket Mounting Screws on both sides of the Leg Top Bracket are tight. Retighten if necessary. Check all legs.
2.Leg pivot or ‘swing’ adjustment to ensure firm, smooth resistance.
Tighten the Leg Pivot Screws on each side of the Leg Top Bracket using a 4mm Hex key until a smooth resistance is maintained. Check all legs.
Leg Top Bracket | 4mm Hex Key | |
Leg Pivot Screw | ||
|
#2 Pozi Head
Screw Driver
Bracket Mounting | Fig 9. |
| |
Screws |
|
SAFETY
Ensure that all equipment is operating correctly and free from defects and
damage, also please ensure that the tripod is steady, secure and that the
bowl is approximately horizontal when attaching the camera. The operator is responsible for the safe operation of this equipment.
1.Do not exceed the maximum payload capacity of the Tripod.
2.Do not leave the camera unattended on the Fluid Head.
3.Do not adjust the tripod Leg locks whilst the camera is attached to the Fluid Head.
4.Do not move the Tripod whilst the camera is attached to the Fluid Head.
5.Do not remove the Mid Level Spreader or Ground Spreader whilst the camera and fluid head is attached.
MAINTENANCE
Regularly inspect the tripod, paying particular attention to any tube damage, leg lock adjustment, leg top adjustment, condition of the bowl rim, spreader mounting points, carry handle and feet.
Keep grit and dirt out of Sprint Loks as much as possible, including behind levers. Regularly clean the tripod with a clean damp rag or soft brush. Wipe
off all sand, dust and salt spray.
Do not clean with solvents, cleaning fluids, lubricants, polishes, abrasives
or wire brushes.
Transport and store the tripod in Miller case wherever possible. Store the
tripod in a dry place, away from direct sunlight.