Ikelite S200 instruction manual Optional Accessories, Control Maintenance

Optional Accessories

Substrobe DS125 Package #3944.77 The Substrobe DS125package includes the Substrobe DS125,the EV Controller, ball socket arm and charger. The EV Controller provides 10manual power settings in 1/2 stop increments. An external strobe offers several advantages over using the camera’s built-in flash. External strobes move the flash away from the camera lens which helps reduce backscatter. They also expand lighting options to achieve the best lighting for different subjects. A second external digital strobe package can be added to fill the shadows and produce more realistic photographs.

The Substrobe DS125covers the equivalent of a 18mm lens, 100 degrees. It is the ideal choice when using accessory wide angle lenses greater than 28mm.

13

Substrobe

DS125

Ball Socket

Arm

EV Controller

NOTE:

Optional Tray and Release Handle required to mount Substrobes.

Maintenance
The Ikelite Digital Housing should be given the same care and
attention as your other photographic equipment. In addition to
normal maintenance we recommend that the housing be returned
to Ikelite periodically to be checked and pressure tested.
1.	Do Not leave the camera and housing in direct sunlight for
2.	prolonged periods. Heat may damage the camera.
	Do Not ship the camera in the housing.
3.	Before using the housing, always check the tightness of the set
	screw in each control knob.
	Check each control gland penetrating the housing to make sure
	they are tight. There is a slight chance that either could vibrate
4.	loose during travel.
	Keep the back o-ring clean and lightly lubricated. To lubricate
	remove the o-ring from the back. Put a small amount of lkelite
	lubricant on your fingers. Draw the o-ring through your fingers
	to apply a light coating of lubricant. Only apply enough
	lubricant to make the o-ring feel slick. Do Not stretch the
	o-ring. This light coating of lubricant will help to keep the o -
	ring from drying out and will help to show a dark sealing line
5.	when the housing back is properly sealed.
	Keep the area where the o-ring fits and the sealing surface of
6.	the housing clean.
	Rinse the housing exterior thoroughly in fresh water after each
	salt water use. Dry with a soft cloth. Dry lens port to eliminate
	water spotting.
	After several uses in salt water soak the housing exterior in a
	mild soap solution, rinse and dry before storage. When storing
	the housing, remove the back o-ring, lightly lubricate and place
	in a plastic bag. Place the plastic bag with o-ring inside the
	housing for safe keeping.
CAUTION
	Never use spray lubricants as the propellant ingredient can	14
	cause the plastic housing to crack.

Control Maintenance

Ikelite controls are designed to provide years of reliable service with minimal maintenance.

1. Push button controls require no maintenance other than rinsing in fresh water after saltwater use. If a push button control becomes difficult to push or if it sticks when depressed, soak the housing in luke warm fresh water. After a few minutes operate the push button. If this does not correct the problem, return the housing to Ikelite for maintenance.

lubricate shaft

housing

pull out to expose shaft

Control Maintenance Cont.

3. Some of the controls have a short shaft and cannot be pulled out exposing the shaft for lubrication. In the unlikely event one of these controls sticks or becomes difficult to operate you can remove the control from the housing and lubricate it, or return the housing to Ikelite for maintenance. To remove the control, loosen the set screw in the knob (allen wrench required); remove the knob. If there is salt or dirt build-up on the exposed control shaft, clean the shaft. Open the housing and gently slide the control shaft out of the control gland. Clean and lightly lubricate the shaft, including the end of the shaft. Slide the shaft back into the control gland and gently slide it back and forth a few times without fully removing the shaft from the gland. Replace the knob, NOTE the flat area on the shaft, the set screw in the knob should tighten down against the flat area on the control so the knob does not turn on the shaft.

2.Some of the controls have long shafts. These controls can be pulled out, exposing the shaft (see drawing).

To lubricate the control, gently pull on the knob until the stainless steel shaft is exposed. Lightly lubricate the shaft, then move the shaft in and out several times. This will lubricate the x-ring in the Ikelite control gland. This should be done before using the housing after a prolonged storage period, or once a week when the housing is in use.

control	housing	gland
shaft

Flat Tighten set screw down against this area when

replacing the knob. Lubricate end of shaft before reinserting into gland

Loosen set screw (allen wrench required)

15 16