Control Maintenance

Optional Accessories Continued

AF35 Autoflash kit includes:

-AF35 strobe

-Flex arm

-AutoFlash sensor

-Handle with rubber grip

-Tray (single or dual)

-Mounting hardware

The Autoflash AF35 replicates your camera's flash for automatic exposure in any situation. Single or dual trays can attach directly to your housing. The exposure selector dial on the side of the sensor provides fine tuning to optimize results with a variety of digital still cameras. Once you find an exposure level that you like, leave the dial on that number for automatic operation.

Complete information regarding optional accessories available at

www.ikelite.com13

Ikelite controls are designed to provide years of reliable service with minimal maintenance.

1. Push button controls require no maintenance other than rinsing in fresh water after saltwater use. If a push button control becomes difficult to push or if it sticks when depressed, soak the housing in luke warm fresh water. After a few minutes operate the push button. If this does not correct the problem, return the housing to Ikelite for maintenance.

lubricate shaft

housing

pull out to expose shaft

Maintenance

The Ikelite Digital Housing should be given the same care and attention as your other photographic equipment. In addition to normal maintenance we recommend that the housing be returned to Ikelite periodically to be checked and pressure tested.

1. Do Not leave the camera and housing in direct sunlight for prolonged periods. Heat may damage the camera.

2. Do Not ship the camera in the housing.

3. Before using the housing, always check the tightness of the set screw in each control knob.

Check each control gland penetrating the housing to make sure they are tight. There is a slight chance that either could vibrate loose during travel.

4. Keep the back o-ring clean and lightly lubricated. To lubricate remove the o-ring from the back. Put a small amount of lkelite lubricant on your fingers. Draw the o-ring through your fingers to apply a light coating of lubricant. Only apply enough lubricant to make the o-ring feel slick. Do Not stretch the o-ring. This light coating of lubricant will help to keep the o-ring from drying out and will help to show a dark sealing line when the housing back is properly sealed.

5. Keep the area where the o-ring fits and the sealing surface of the housing clean.

6. Rinse the housing exterior thoroughly in fresh water after each salt water use. Dry with a soft cloth. Dry lens port to eliminate water spotting.

After several uses in salt water soak the housing exterior in a mild soap solution, rinse and dry before storage. When storing the housing, remove the back o-ring, lightly lubricate and place in a plastic bag. Place the plastic bag with o-ring inside the housing for safe keeping.

Control Maintenance Cont.

3. Some of the controls have a short shaft and cannot be pulled out exposing the shaft for lubrication. In the unlikely event one of these controls sticks or becomes difficult to operate you can remove the control from the housing and lubricate it, or return the housing to Ikelite for maintenance. To remove the control, loosen the set screw in the knob (allen wrench required); remove the knob. If there is salt or dirt build-up on the exposed control shaft, clean the shaft. Open the housing and gently slide the control shaft out of the control gland. Clean and lightly lubricate the shaft, including the end of the shaft. Slide the shaft back into the control gland and gently slide it back and forth a few times without fully removing the shaft from the gland. Replace the knob, NOTE the flat area on the shaft, the set screw in the knob should tighten down against the flat area on the control so the knob does not turn on the shaft.

2.Some of the controls have long shafts. These controls can be pulled out, exposing the shaft (see drawing).

To lubricate the control, gently pull on the knob until the stainless steel shaft is exposed. Lightly lubricate the shaft, then move the shaft in and out several times. This will lubricate the x-ring in the Ikelite control gland. This should be done before using the housing after a prolonged storage period, or once a week when the housing is in use.

control	housing	gland
control	housing	gland
shaft

Flat Tighten set screw down against this area when

replacing the knob. Lubricate end of shaft before reinserting into gland

Loosen set screw (allen wrench required)

6184.7 specifications

The Ikelite 6184.7 is a highly regarded underwater camera housing designed specifically for the Canon EOS R mirrorless camera system. This housing is known for its robust construction, innovative features, and user-friendly design, making it an excellent choice for both amateur and professional underwater photographers.

One of the standout features of the Ikelite 6184.7 is its durable construction. Made from lightweight yet sturdy ABS polycarbonate, the housing provides excellent protection against the harsh underwater environment. It is designed to resist corrosion and withstand significant water pressure, making it suitable for depths of up to 60 meters (200 feet). This durability ensures that photographers can focus on capturing stunning underwater images without worrying about their equipment.

The housing is equipped with a clear back to provide a full view of the camera controls and status while allowing users to monitor their camera settings easily. The design includes precise cutouts for buttons, allowing for comfortable access to essential controls without the need to remove the housing. This feature is particularly beneficial in dynamic underwater environments, where adjusting settings quickly can be crucial.

Another significant aspect of the Ikelite 6184.7 is its compatibility with a range of lenses. Designed to accommodate Canon's full-frame RF lenses, photographers have the flexibility to choose from a variety of optical options to suit their shooting style. Furthermore, the housing supports the use of dedicated ports, giving users the choice to use different lens types, including wide-angle and macro lenses, to capture stunning close-ups or expansive underwater scenes.

For enhanced underwater imaging, the Ikelite 6184.7 supports the use of powerful external strobes and lighting systems. It features dual removable flash sync connectors, making it easy to connect and synchronize with Ikelite’s popular strobe lights. This capability allows photographers to achieve superior lighting and color balance in their underwater photographs, resulting in more vibrant and lifelike images.

In addition to its functional features, the Ikelite 6184.7 is designed with an intuitive interface, making it suitable for photographers of all skill levels. The housing is lightweight and compact, which facilitates easy handling underwater. Overall, the Ikelite 6184.7 is an exceptional housing option for Canon EOS R users seeking to explore the captivating world beneath the waves. With its blend of durability, versatility, and user-friendly design, it stands out as a favorite among underwater imaging enthusiasts.