Yamaha DSP-AX861SE owner manual 91 En, SCENE IR code setting SCENE IR, Bi-amplifiersetting BI-AMP

Page 93
Remote control AMP ID codes

4Press the numeric buttons (F) to enter the four-digit remote control code for the input area you want to use.

CLASSICAL LIVE/CLUB ENTERTAIN MOVIE

1 2 3 4

STEREO ENHANCER SUR. DECODE NIGHT

5 6 7 8

9 0

Remote control AMP ID codes

Select one of the following codes to set the remote control AMP ID code for the input area you want to use.

AMP ID code

 

Remote

(remote control

Function

control AMP

setting)

 

ID

 

 

 

2001

To operate this unit using the

ID1

(initial setting)

default code.

(initial setting)

 

 

 

2002

To operate this unit using an

ID2

 

alternative code.

 

 

 

 

 

5Press DENTER to set the number.

“OK” appears in the display window (J) if setting

was successful.

“NG” appears in the display window (J) if the setting was unsuccessful. In this case, start over from step 1.

6Press TLEARN again to exit from the setup mode.

LEARN

Advanced setup

See page 89 for the operation of the advanced setup.

■SCENE IR code setting SCENE IR

Use this feature to output the remote control signals at the REMOTE OUT jack automatically when this unit is in the SCENE mode.

Choices: ON, OFF

•Select “ON” when the component connected to the REMOTE OUT jack is the Yamaha component and has the capability of the SCENE control signals. This unit automatically sends the remote control signals to the component.

•Select “OFF” when the component connected to the REMOTE OUT jack is not the Yamaha component and does not have the capability of the SCENE control signals.

Note

If noises are output when you operate the SCENE function, set “SCENE IR” to “OFF”.

■Bi-amplifier setting BI-AMP

Use this feature to activate or deactivate the bi-amplifier function (see page 14).

Choices: ON, OFF

•Select “ON” if you want to activate the bi-amplifier function. “SUR.B L/R SP” is set to “NONE” automatically, and this unit outputs the front channel audio signals at the SURROUND BACK speaker terminals.

•Select “OFF” if you want to deactivate the bi-amplifier function.

Note

When “BI-AMP” is set to “ON”, you can only select “FRONT B” or “NONE” in “EXTRA SP ASSIGN” (see page 64).

■Video parameter reset V.RESET

Use this feature to initialize the “VIDEO CONV.”, “HDMI UP-SCALING”, “HDMI ASP” and “OSD SHIFT” settings in “DISPLAY SET” (see page 73). Choices: YES, CANCEL

■Monitor check MON.CHK

Use this feature to activate or deactivate the monitor check function of this unit. When this parameter is set to “YES”, this unit receives the information of the available video signal resolutions from the video monitor connected via HDMI (see page 73).

Choices: YES, SKIP

OPERATION

ADVANCED

 

 

English

91 En

Page 92 Page 94
Image 93
Page 92 Page 94
Contents DSP-AX861SE AV AmplifierOWNER’S MANUAL Caution: Read this before operating your unit For U.K. customersSpecial Instructions for U.K. Model Contents 1 Enat the end of this manual Notice 2 EnAbout this manual Supplied accessories FeaturesBuilt-in 7-channelpower amplifier Other featuresGetting started Installing batteries in the remote control 2 34 En 2Insert the four supplied batteriesQuick start guide Step 1: Set up your speakersPreparation: Check the items Enjoy DVD playback1Place your speakers and subwoofer in the room 6 En2Connect speaker cables to each speaker Front speakers and center speaker1 Connect the digital coaxial audio cable to the 7 Endigital coaxial audio output jack of your DVD player and the DVD DIGITAL INPUT COAXIALP. •Connecting a set-topbox P. •Using the other kind of speaker combinations P.P. •Connecting an external amplifier P. P. •Connecting a Yamaha iPod universal dock P.4Rotate 4VOLUME to adjust the volume Using the other SCENE buttons9 En Check the type of the connected speakersUsing various input sources After using this unitUsing various sound features Adjusting the parameters of this unitConnections Rear panel11 En 12 En Placing speakersFront left and right speakers FL and FR Center speaker C13 En Connecting speakersUsing bi-amplificationconnections Connecting the speaker cable4Tighten the knob to secure the wire 14 En15 En Information on jacks and cable plugsAudio jacks Video jacks16 En Information on HDMIHDMI compatibility with this unit HDMI jack and cable plugAudio signal flow Audio and video signal flowVideo signal flow 17 En18 En Connecting a TV monitor or projectorConnecting a DVD player Connecting other components19 En NotesConnecting a set-topbox Connecting a DVD recorder, PVR or VCR20 En ConnectionsConnecting audio components 21 EnNotes 22 En Connecting an external amplifier1FRONT PRE OUT jacks 2SURROUND PRE OUT jacksConnecting a Yamaha iPod universal dock Using the VIDEO AUX jacks on the front panelUsing REMOTE OUT jacks 23 EnAC OUTLET SWITCHED Connecting the power cable24 En Memory back-upTurning this unit on and off Setting the speaker impedance25 En Turning on this unit9 MUTE indicator 1A Input signal indicators2B Decoder indicators 3ENHANCER indicatorLInput channel and speaker indicators Using the remote controlLFE indicator Input channel indicators28 En Using AUTO SETUP2 Connect the supplied optimizer microphone to the OPTIMIZER MIC jack on the front•When you do not use the EXTRA SP terminals •When you use the presence speakers see page5Press Dl / h to select “SETUP” and then 6Press Dl/ hto select the desired setting of “EQ”30 En Speaker wiring WIRINGSpeaker size SIZE Speaker distance DISTANCEselect “SET” or “CANCEL” the setup result displays31 En 9Press Dl / h repeatedly to toggle between32 En If an error screen appearsIf “WARNING” appears 3Press DENTER to return to the topSelecting the desired SCENE template Selecting the SCENE templatesDVD Viewing DVD MovieWhich SCENE template would you like to select? 34 EnDefault SCENE buttons Which source do you like to play back?35 En Preset SCENE templates descriptionsDVD Viewing DVD Movie Viewing36 En Creating your original SCENE templatesRename the SCENE templates 2Set the operation mode selector to LAMPPlayback Basic procedure37 En the desired input sourceUsing the Zone B feature A quick guide to contentsSelecting the MULTI CH INPUT component Selecting the front speaker set39 En Selecting audio input jacks AUDIO SELECTcontrol 1Turn on the video monitor connected to this unit2Press Dn repeatedly to select “SIGNAL Using your headphones4Press NSET MENU on the remote control Muting the audio outputCanceling the sleep timer Using the sleep timer41 En Audio informationSound field programs Sound field indicatorsSelecting sound field programs Sound field program descriptionsFor audio music sources 43 EnHiFi DSP NotesFor various sources 44 EnFor visual sources of music Notes45 En For movie sourcesNotes Stereo playback 46 EnThe Compressed Music Enhancer Virtual CINEMA DSP47 En STRAIGHTDeactivating the “STRAIGHT” mode Press 7STRAIGHT or QSTRAIGHT to select “STRAIGHT”Adjusting the tonal quality Using audio featuresAdjusting the speaker level 2Press Dl / h to adjust the speaker output levelSelecting the night listening mode Enjoying multi-channelsources in 2-channelstereoEffect.Lvl:MID 49 EnControlling iPod Using iPod50 En Controlling iPod in the simple remote modeThe function of the play information display 51 En1Set the operation mode selector to playback of the selected song52 En Recording1Turn on all the connected components the source component you want to record fromsettings Advanced sound configurationsadjust Changing sound field parameter54 En Basic configuration of sound field programsIncrease the value of “DSP LEVEL” when Decrease the value of “DSP LEVEL” whenINIT.DLY P.INIT.DLY S.INIT.DLY SB INI.DLY 55 En56 En ROOM SIZE P.ROOM SIZE S.ROOM SIZE SB ROOM SIZELIVENESS S.LIVENESS SB LIVENESS REV.TIME 57 EnREV.DELAY REV.LEVEL58 En Selecting decodersSelecting decoders used with sound field programs Decoder TypeDecoder descriptions 59 EnSURROUND DECODE SURROUND DECODEDecoder parameter descriptions 60 EnAuto setup AUTO SETUP Customizing this unit MANUAL SETUPManual setup MANUAL SETUP 61 En62 En Signal information SIGNAL INFOSETUP” Using SET MENUsettings 6Press NSET MENU to exit from “SET MENU” 63 EnWhen you use the presence speakers see page Speaker settings ASPEAKER SETWhen you do not use the EXTRA SP terminals FRONT B speakers setting FRONT BWhen the front speakers are small When the front speakers are largeWhen the center speaker is large When the center speaker is smallSubwoofer phase SUBWOOFER PHASE When you do not use a subwoofer66 En LFE/Bass out LFE/BASS OUTSpeaker distance CSP DISTANCE 67 EnUnit UNIT Speaker distances68 En Audio settings GAUDIO SETLow-frequencyeffect level Center graphic equalizer CENTER GEQMaximum volume MAX VOL HDMI setting HHDMI SETInitial volume INI.VOL 69 En70 En 2 INPUT MENUInput/output assignment For COMPONENT VIDEO jacks A, B and C71 En 5Press DENTER on the remote control to exitFor OPTICAL OUTPUT jack For OPTICAL INPUT jacks 2, 3 andDTS decoder prioritize setting Multi channel input settings72 En Decoder select mode3 OPTION MENU Display settings ADISPLAY SET73 En Video conversion VIDEO CONV74 En Source feature OSD display timeHDMI aspect ratio HDMI ASP Dimmer DIMMER75 En iPod universal dock setting EDOCK SETParameter initialization DPARAM.INI Charge on standby STANDBY CHARGEUsing the remote control for the SCENE feature Remote control featuresremote control 76 En77 En Controlling this unit, a TV, or other componentsControlling this unit Controlling a TVControlling other components 78 EnRemote control code default settings Setting remote control codesyou want to set up 79 En80 En 6Press TLEARN again to exit from the setup mode3Press DENTER 5Press DENTER to set the number81 En Programming codes from other remote controls1 Set the operation mode selector to LSOURCE and then press an input selectorChanging source names in the display window the remote control82 En 5Press and hold the button you want to83 En Macro programming featuresMACRO operations 3Press Dk / n to select and enter a character84 En Default macro functionsor similar object when the operation 4 Press TMACRO again using a ballpoint pen85 En 3 Press the buttons for the functions you wantusing a ballpoint pen or similar object Clearing configurations86 En Clearing function setsClearing a learned function 87 Encontaining the function you want to clear TLEARN again to exitClearing a macro function 88 Ena ballpoint pen or similar object NotesUsing the advanced setup Advanced setup89 En unitRemote control AMP ID REMOTE AMP User presets PRESETSetting remote control AMP ID codes 90 EnBi-amplifiersetting BI-AMP SCENE IR code setting SCENE IRVideo parameter reset V.RESET Remote control AMP ID codes92 En TroubleshootingGeneral after the power isspeakers when the 93 Ensettings are not pageor DTS indicator in 94 EnThe volume level is The volume level95 En Remote control“CHECK SP WIRES” The remote controlBefore AUTO SETUP AUTO SETUP96 En HDMIAfter AUTO SETUP During AUTO SETUP97 En Notes3Rotate the 6PROGRAM selector to select “PRESET” Resetting the system4Press 5TONE CONTROL repeatedly to select “RESET” 98 EnComposite video signal Component video signalGlossary 99 En100 En S-videosignalDTS 96/24 DTS Digital Surround101 En Sound field program informationElements of a sound field CINEMA DSP102 En Parametric equalizer informationFrequency Gain103 En SpecificationsAUDIO SECTION VIDEO SECTIONIndex 104 EnNumerics 105 En 106 En 5 6 7 8 9 0 A Front panelRemote control CABLE List of remote control codesCD PLAYER CD RECORDERMD RECORDER LD PLAYERRECEIVER TUNER SATELLITE TUNERAMERICA ACTION Page HUGHES NETWORK SYSTEMS VOLUME 5 6 7 8 9 0 ADSP-AX861SE/DSP-AX761 Front panel
Top Page Image Contents